ZL6100EVAL1Z Intersil, ZL6100EVAL1Z Datasheet - Page 5

no-image

ZL6100EVAL1Z

Manufacturer Part Number
ZL6100EVAL1Z
Description
EVAL BOARD USB ZL6100
Manufacturer
Intersil
Datasheets

Specifications of ZL6100EVAL1Z

Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ZL6100EVAL1Z
Manufacturer:
Intersil
Quantity:
4
Electrical Specifications
NOTES:
10. V
12. Precise ramp timing mode is only valid when using EN pin to enable the device rather than PMBus enable.
13. The devices may require up to a 4ms delay following the assertion of the enable signal (normal mode) or following the de-assertion of the enable
14. Factory default Power-Good delay is set to the same value as the soft-start ramp time.
15. Percentage of Full Scale (FS) with temperature compensation applied.
16. t
17. Normal capacitance of logic pins is 5pF.
18. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
11. The device requires a delay period following an enable signal and prior to ramping its output. Precise timing mode limits this delay period to
UVLO Set-point Accuracy
UVLO Hysteresis
UVLO Delay
Power-Good V
Power-Good V
Power-Good Delay
VSEN Undervoltage Threshold
VSEN Overvoltage Threshold
VSEN Undervoltage Hysteresis
VSEN Undervoltage/Overvoltage Fault
Response Time
Current Limit Set-point Accuracy
(V
Current Limit Set-point Accuracy
(Ground referenced)
Current Limit Protection Delay
Temperature Compensation of
Current Limit Protection Threshold
Thermal Protection Threshold
(Junction Temperature)
Thermal Protection Hysteresis
8. Does not include margin limits.
9. Percentage of Full Scale (FS) with temperature compensation applied.
OUT
approx 2ms, where in normal mode it may vary up to 4ms.
signal.
SW
OUT
Referenced)
= 1/f
measured at the termination of the VSEN+ and VSEN- sense points.
SW
OUT
OUT
, where f
PARAMETER
Threshold
Hysteresis
SW
is the switching frequency.
5
V
apply over the operating temperature range, -40°C to +85°C. (Continued)
DD
= 12V, T
A
Factory default
Configurable via I
Factory default
Factory default
Using pin-strap or resistor (Note 14)
Configurable via I
Factory default
Configurable via I
Factory default
Configurable via I
Factory default
Configurable via I
Factory default
Configurable via I
Factory default
Configurable via I
Factory default
Configurable via I
= -40°C to +85°C, unless otherwise specified. Typical values are at T
2
2
2
2
2
2
2
2
ZL6100
C/SMBus
C/SMBus
C/SMBus
C/SMBus
C/SMBus
C/SMBus
C/SMBus
C/SMBus
CONDITIONS
(Note 18)
-150
MIN
100
-40
0
0
0
0
0
5
1
4400
TYP
±10
±10
125
115
90
85
16
15
3
5
5
5
A
= +25°C. Boldface limits
(Note 18)
12700
MAX
150
100
200
500
110
115
125
2.5
60
32
December 15, 2010
(Note 15)
(Note 15)
(Note 16)
(Note 16)
% V
% V
% V
% V
% V
% V
ppm/°C
ppm/°C
% FS
% FS
UNIT
FN6876.2
mV
t
t
ms
µs
µs
µs
°C
°C
°C
%
%
%
SW
SW
s
OUT
OUT
OUT
OUT
OUT
OUT

Related parts for ZL6100EVAL1Z