LPC1113FBD48/301 NXP Semiconductors, LPC1113FBD48/301 Datasheet - Page 27
![MCU, 32BIT, 24K FLASH, CORTEX-M0, 48LQFP](/photos/19/0/190032/ge48lqfp05-40_sml.jpg)
LPC1113FBD48/301
Manufacturer Part Number
LPC1113FBD48/301
Description
MCU, 32BIT, 24K FLASH, CORTEX-M0, 48LQFP
Manufacturer
NXP Semiconductors
Datasheet
1.LPC1111FHN33101.pdf
(66 pages)
Specifications of LPC1113FBD48/301
Controller Family/series
ARM Cortex-M0
No. Of I/o's
42
Ram Memory Size
8KB
Cpu Speed
50MHz
No. Of Timers
4
Core Size
32bit
Program Memory Size
24KB
Oscillator Type
External, Internal
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LPC1113FBD48/301
Manufacturer:
NXP
Quantity:
5 600
Company:
Part Number:
LPC1113FBD48/301,1
Manufacturer:
NXP
Quantity:
1 250
Company:
Part Number:
LPC1113FBD48/301,1
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
LPC1111_12_13_14
Product data sheet
7.15.1.2 System oscillator
7.15.1.3 Watchdog oscillator
7.15.2 System PLL
7.15.3 Clock output
7.15.4 Wake-up process
7.15.5 Power control
Upon power-up or any chip reset, the LPC1111/12/13/14 use the IRC as the clock source.
Software may later switch to one of the other available clock sources.
The system oscillator can be used as the clock source for the CPU, with or without using
the PLL.
The system oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can be
boosted to a higher frequency, up to the maximum CPU operating frequency, by the
system PLL.
The watchdog oscillator can be used as a clock source that directly drives the CPU, the
watchdog timer, or the CLKOUT pin. The watchdog oscillator nominal frequency is
programmable between 7.8 kHz and 1.7 MHz. The frequency spread over processing and
temperature is ±40 %.
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up to a high frequency with a Current Controlled Oscillator (CCO).
The multiplier can be an integer value from 1 to 32. The CCO operates in the range of
156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within
its frequency range while the PLL is providing the desired output frequency. The PLL
output frequency must be lower than 100 MHz. The output divider may be set to divide by
2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2, it is
insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed
following a chip reset and may be enabled by software. The program must configure and
activate the PLL, wait for the PLL to lock, and then connect to the PLL as a clock source.
The PLL settling time is 100 μs.
The LPC1111/12/13/14 features a clock output function that routes the IRC oscillator, the
system oscillator, the watchdog oscillator, or the main clock to an output pin.
The LPC1111/12/13/14 begin operation at power-up and when awakened from Deep
power-down mode by using the 12 MHz IRC oscillator as the clock source. This allows
chip operation to resume quickly. If the system oscillator or the PLL is needed by the
application, software will need to enable these features and wait for them to stabilize
before they are used as a clock source.
The LPC1111/12/13/14 support a variety of power control features. There are three
special modes of processor power reduction: Sleep mode, Deep-sleep mode, and Deep
power-down mode. The CPU clock rate may also be controlled as needed by changing
clock sources, reconfiguring PLL values, and/or altering the CPU clock divider value. This
allows a trade-off of power versus processing speed based on application requirements.
In addition, a register is provided for shutting down the clocks to individual on-chip
All information provided in this document is subject to legal disclaimers.
Rev. 4 — 10 February 2011
32-bit ARM Cortex-M0 microcontroller
LPC1111/12/13/14
© NXP B.V. 2011. All rights reserved.
27 of 66