CS1W-CN713 Omron, CS1W-CN713 Datasheet - Page 150
CS1W-CN713
Manufacturer Part Number
CS1W-CN713
Description
"CABLE CS1 EXP I/O,70cm"
Manufacturer
Omron
Datasheet
1.CS1W-CN313.pdf
(152 pages)
Specifications of CS1W-CN713
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 150 of 152
- Download datasheet (3Mb)
Programming Console
Connection
4-10 Connecting Programmable Terminals
128
Connecting Programmable Terminals
Note
Note When connecting the CQM1H to a Programming Console, be sure to turn
The CQM1H CPU Unit can be connected to a Programming Console as
shown below.
OFF pin 7 on the DIP switch (factory setting). If pin 7 is ON, it will not be pos-
sible to use a Programming Console.
The different communications configurations available for communications
with a Programming Terminal (PT) are shown in the following table.
1. When communicating via a 1:1-mode NT Link, connect to the port on the
2. When communicating via a 1:N-mode NT Link, connect to the port on the
3. The NT20S, NT600S, NT30, NT30C, NT620S, NT620C, and NT625C can-
4. The Programming Console functions of the PT (Expansion Mode) cannot
5. Set a unique unit number for each PT connected to the same PC. If the
CPU Unit’s built-in RS-232C
port
Serial Com-
munications
Board
Serial communications
PT that supports this mode. Communications will not be possible if con-
nection is made to a port that supports only 1:N-mode communications.
PT that supports this mode. Communications will not be possible if con-
nection is made to a port that does not support this mode (e.g., the RS-
232C port on the NT30/NT30C supports only 1:1 communications).
not be used if the cycle time of the CPU Unit is 800 ms or longer (even if
only one of these PTs is used in a 1:N NT Link.)
be used when connected to Serial Communications Board ports. They can
be used only by connecting to the RS-232C port on the CPU Unit.
Turn ON pin 7 on the DIP switch on the CPU Unit when using the Program-
ming Console function of the PT.
same unit number is set for more than one PT, malfunctions will occur.
Programming
Console
port
RS-232C port
(port 1)
RS-422A/485
(port 2)
CQM1H
nications mode
NT Link
(1:1 mode)
NT Link
(1:1 mode,
1:N mode)
NT Link
(1:1 mode,
1:N mode)
Peripheral port
Serial commu-
One-to-one only
One-to-one or
one-to-many
One-to-one or
one-to-many
PC-to-PT ratio
Section 4-10
Supported
(from PT)
No
No
Programming
functions
Console
Related parts for CS1W-CN713
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MODULE,ANALOG OUT,4CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MODULE, ANALOG IN, 8CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Connector Cable
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Cable Connector
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
"BATTERY,CPU,CS1 SERIES ONLY"
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
"CABLE,CS1/ CQM1-PRO01,0.1m"
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
BACKPLANE,CS1 CPU,3 SLOTS
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
"BACKPLANE,CS1 CPU,8 SLOTS"
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: