R88A-CSU015C Omron, R88A-CSU015C Datasheet - Page 204
R88A-CSU015C
Manufacturer Part Number
R88A-CSU015C
Description
ABSOLUTE ENCODER CABLE,15M
Manufacturer
Omron
Datasheet
1.R88A-CAU001.pdf
(324 pages)
Specifications of R88A-CSU015C
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 204 of 324
- Download datasheet (3Mb)
Application
A.L03
A.L06
A.L07
A.L09
A.L10
A.L12
A.L15
A.L16
Alarm dis-
play
Voltage drop
Resolver discon-
nection
Power status
error
Regeneration
Resistor over-
heat
Regeneration
operation error
Clock stop
Overcurrent
(soft)
(
[Th
[The current
exceeded the
motor’s rated
motor’s rated
current (120%).]
Speed amp satu-
ration
[Th
[The speed amp
was saturated for
more than 3
more than 3
seconds.]
Error content
)
d
t
Occurred during
operation.
Occurred during
motor acceleration
Occurred when
power was turned
ON
ON.
Occurred after
slight movement at
the beginning.
---
Occurred during
operation.
Occurred during
operation.
---
Occurred during
operation.
Occurred during
operation.
Condition when
error occurred
The power supply voltage fell
below the prescribed value.
The power supply capacity is
insufficient.
The UP-02 (applicable motor)
setting is wrong.
The resolver’s wiring is dis-
connected or faulty.
There is poor contact at the
connectors.
An error occurred in the main
circuit.
The regenerative absorption
exceeded the internal absorp-
tion.
The power supply voltage is
outside the allowable range.
The Regeneration Resistor is
damaged.
An external Regeneration
Resistor is not being used and
the short bar has been
removed from between JP1
and JP2 on the terminal block.
The regeneration circuit is
damaged.
The Position Driver’s internal
clock has stopped.
The mechanical system is
locked.
The power lines are wired
incorrectly.
The power lines are shorted-
circuited or grounded.
The UP-02 (applicable motor)
setting is wrong.
The mechanical system is
locked.
The power lines are wired
incorrectly.
The UP-02 (applicable motor)
setting is wrong.
Probable cause
Increase the power supply
capacity.
Set the motor model code cor-
rectly.
Make sure the connectors are
inserted firmly and locked into
place.
Replace the Driver.
Connect an external Regen-
eration Resistor.
Use a 170 to 264-VAC power
supply.
Mount a short bar between
JP1 and JP2.
Replace the Driver.
Replace the Driver.
Correct the places that are
locked.
Correct the wiring.
Correct the short-circuiting or
grounding.
Set the motor model code cor-
rectly.
Correct the places that are
locked.
Correct the wiring.
Set the motor model code cor-
rectly.
For 200-VAC input specifi-
cations, use a 170 to
264-VAC power supply.
For 100-VAC input specifi-
cations, use an 85 to
127-VAC power supply.
Connect any places that are
disconnected.
Correct the wiring.
Replace the external
Regeneration Resistor.
If an external Regeneration
Resistor is not being used,
replace the Driver.
Countermeasures
Chapter 4
4-13
Related parts for R88A-CSU015C
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: