GP2W0110YPSF Sharp Microelectronics, GP2W0110YPSF Datasheet - Page 9
![Fiber Optic Transmitters, Receivers, Transceivers GP2W0110YPSF Side View T&R](/photos/26/68/266824/gp2w_sml.jpg)
GP2W0110YPSF
Manufacturer Part Number
GP2W0110YPSF
Description
Fiber Optic Transmitters, Receivers, Transceivers GP2W0110YPSF Side View T&R
Manufacturer
Sharp Microelectronics
Datasheet
1.GP2W0110YPSF.pdf
(10 pages)
Specifications of GP2W0110YPSF
Product
Transceiver
Data Rate
115.2 Kbps
Wavelength
870 nm
Maximum Rise Time
600 ns, 60 ns
Maximum Fall Time
600 ns, 60 ns
Pulse Width Distortion
300 us, 6 us
Operating Supply Voltage
2 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 25 C
Idle Current, Typ @ 25° C
90µA
Link Range, Low Power
20cm
Operating Temperature
-25°C ~ 85°C
Orientation
Top View
Shutdown
*
Size
7.6mm x 2.65mm x 2mm
Standards
-
Supply Voltage
2 V ~ 3.6 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
GP2W0110YPSF
Manufacturer:
AVAGO
Quantity:
265
Test and Evaluation Board
Sharp Microelectronics has prepared an evaluation board for preliminary test of the GP2W0110YP0F transceiver.
This board has also been developed to support the GP2W0112YPS transceiver, and that is why there are two
resistor positions on the board. In the configuration for GP2W0110YP0F, R2 = 0 Ohms, and the R1 position is
open. (The position for R1 will be loaded when the board is used for GP2W0112YP.)
The new low power 20 cm transceivers are so small that soldering directly to the contacts on the device is not an
easy or effective connection method. Testing with an actual surface mount connection is the best method for
evaluation. The PCB provides the electrical interface and a good ground-plane for test purposes. Connector J1 is
the interface to the test system. The drawing shows that the device EMI shield should be connected to a good
Ground in your final system.
The value of capacitor CX1 is listed as 10 µF. This value should be modified to meet your system electrical noise
requirements. The decision should be based on the amount of system noise at the point where the IrDA
transceiver will be powered. Both time-domain and frequency-domain noise issues should be considered. One
common source of noise is switching power supplies, which need attention both on the power line and ground
return paths.
As shown, capacitor CX1 is the only external component needed with the transceiver. If the power supply filtering
in your system design is such that no capacitor is needed, there is no absolute requirement for it and that is a
decision left to the design engineer.
Note
powered from the same source, pins 2 and 10 needs to be externally connected.
Evaluation boards may be requested through any Sharp Microelectronics of the Americas Sales office.
LIFE SUPPORT POLICY
SHARP components should not be used in medical devices with life support functions or in safety equipment (or
similar applications where component failure result in loss of life or physical harm) without the written approval of
an officer of the SHARP Corporation.
SHARP reserves the right to make changes in specifications at any time and without notice. SHARP does not
SHARP Electronic Components
Rev. 1.2
(Technical Information DISCLAIMER)
ELECTRONIC COMPONENTS
This document is provided as a technical Guide for the Sharp GP2W0110YP0F Infrared Transceiver. Any of
information under this document is applicable only for design reference purpose, and Sharp holds the right to change
and alter information and prices at any time without notice.
Contact SHARP, the Sharp web site or SHARP local representatives in order to obtain the latest version of the device
Specification Sheets before using any SHARP’s devices. In absence of confirmation by device Specification Sheets,
SHARP takes no responsibility for any defects that occur in equipment using any of SHARP’s device, shown in
catalogues, data books, Preliminary Information, etc.
GND
SD
that the V
1
3
5
7
9
, March 7, 2002
+
+
+
+
+
2 X 5
J1
+
+
+
+
+
2
4
6
8
10
VCC
VLEDA
DD
RXD
VCC
connection and V
TXD
LEDA
connections are now on separate pins. If V
+
IrDA Low Power Infrared Transceiver
10 uF 6.3V
CX1
R2 0 Ohms
R1 OPTION
DD
and V
GP2W0110YP
2
3
1
4
5
6
7
8
NC
NC
VDD
GND
SD
RXD
TXD
LEDA
LEDA
are to be
GND
9