PD93-21C Everlight Electronics CO., LTD, PD93-21C Datasheet
PD93-21C
Specifications of PD93-21C
Related parts for PD93-21C
PD93-21C Summary of contents
Page 1
... RoHS compliant version. Descriptions PD93-21C is a PIN photodiode in miniature SMD package which is molded in a water clear with flat top view lens. The device is spectrally matched to infrared emitting diode. Applications ․High speed photo detector ․ ...
Page 2
... Power Dissipation at(or below) 25℃Free Air Temperature Notes: *1:Soldering time≦5 seconds. Everlight Electronics Co., Ltd. Device No:DPD-093-069 Symbol Rating -25 ~ +85 opr T -40 ~ +85 stg T 260 sol P 150 c http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C Units V ℃ ℃ ℃ mW Rev 2 Page Prepared by:Jaine Tsai ...
Page 3
... Ee=1mW/ λp=875nm 2 Ee=1mW/cm λp=870nm = Ee=0mW/ =10V R 2 Ee=0mW/ =100μ Ee=0mW/ = f=1MHz =10V R R =1000Ω http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C Min Typ Max Unit 400 --- 1100 nm --- 940 --- nm --- 0.42 --- V μA --- 1.2 --- μA --- 1.2 --- --- --- 170 --- V --- 5 --- pF --- 6 --- nS --- 6 --- Rev 2 Page Prepared by:Jaine Tsai ...
Page 4
... Fig.2 Spectral Sensitivity 1.0 0.8 0.6 0.4 0 100 Fig.4 Reverse Light Current vs. 3.5 3.0 1.5 1.0 V =10V R 0.5 80 100 http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C C Ta=25 100 300 500 700 900 Ee 0.5 1.5 1.0 2 Rev 2 Page Prepared by:Jaine Tsai 1100 1300 V =5V R 3.0 ...
Page 5
... Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Reverse Voltage 0.1 1 Everlight Electronics Co., Ltd. Device No:DPD-093-069 Fig.6 Response Time vs. 10 f=1MH 100 http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C Load Resistance 1 V =10V R Ta=25° Rev 2 Page Prepared by:Jaine Tsai ...
Page 6
... Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No:DPD-093-069 http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C Rev 2 Page Prepared by:Jaine Tsai ...
Page 7
... Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No:DPD-093-069 http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C Rev 2 Page Prepared by:Jaine Tsai ...
Page 8
... Test Hours/ Cycles 6Mins 15mins 50Cycles 5mins 15mins 5mins 50Cycles 10secs 5mins 1000hrs 1000hrs =5V 1000hrs R 1000hrs http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C Sample Failure Sizes Judgement Criteria 22pcs ≦ L × 0 22pcs L : Lower Specification Limit 22pcs 22pcs 22pcs 22pcs 22pcs Rev 2 Page Prepared by: ...
Page 9
... P/N : Production Number QTY: Packing Quantity RoHS CAT: Ranks REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com http:\\www.everlight.com Prepared date:07-20-2005 PD93-21C HUE: Peak Wavelength Rev 2 Page Prepared by:Jaine Tsai ...