AD9516-3BCPZ-REEL7 Analog Devices Inc, AD9516-3BCPZ-REEL7 Datasheet - Page 32
![IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9516-3BCPZ-REEL7
Manufacturer Part Number
AD9516-3BCPZ-REEL7
Description
IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Clock Generator, Fanout Distributionr
Datasheet
1.AD9516-3BCPZ.pdf
(80 pages)
Specifications of AD9516-3BCPZ-REEL7
Pll
Yes
Input
Clock
Output
CMOS, LVDS, LVPECL
Number Of Circuits
1
Ratio - Input:output
1:14
Differential - Input:output
Yes/Yes
Frequency - Max
2.25GHz
Divider/multiplier
Yes/No
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Frequency-max
2.25GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9516-3/PCBZ - BOARD EVAL FOR AD9516-3 2.0GHZ
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9516-3
Phase-Locked Loop (PLL)
The AD9516 includes an on-chip PLL with an on-chip VCO.
The PLL blocks can be used either with the on-chip VCO to
create a complete phase-locked loop, or with an external VCO
or VCXO. The PLL requires an external loop filter, which
usually consists of a small number of capacitors and resistors.
The configuration and components of the loop filter help to
establish the loop bandwidth and stability of the operating PLL.
The AD9516 PLL is useful for generating clock frequencies
from a supplied reference frequency. This includes conversion
of reference frequencies to much higher frequencies for subsequent
division and distribution. In addition, the PLL can be exploited to
clean up jitter and phase noise on a noisy reference. The exact
choices of PLL parameters and loop dynamics are very application
specific. The flexibility and depth of the AD9516 PLL allow the
part to be tailored to function in many different applications
and signal environments.
Configuration of the PLL
The AD9516 allows flexible configuration of the PLL,
accommodating various reference frequencies, PFD comparison
frequencies, VCO frequencies, internal or external VCO/VCXO,
and loop dynamics. This is accomplished by the various settings
that include the R divider, the N divider, the PFD polarity (only
applicable to external VCO/VCXO), the antibacklash pulse
width, the charge pump current, the selection of internal VCO
or external VCO/VCXO, and the loop bandwidth.
REFIN (REF1)
REFIN (REF2)
BYPASS
CLK
CLK
LF
REGULATOR (LDO)
LOW DROPOUT
REF1
REF2
VCO
REF_SEL
SWITCHOVER
REFERENCE
STATUS
STATUS
1
2, 3, 4, 5, OR 6
DIVIDE BY
VS
PRESCALER
0
P, P + 1
GND
N DIVIDER
RSET
DIST
COUNTERS
REF
R DIVIDER
A/B
Figure 46. PLL Functional Blocks
Rev. A | Page 32 of 80
0
1
VCO STATUS
REFMON
PROGRAMMABLE
PROGRAMMABLE
R DELAY
N DELAY
These are managed through programmable register settings (see
Table 52 and Table 54) and by the design of the external loop
filter. Successful PLL operation and satisfactory PLL loop
performance are highly dependent upon proper configuration of
the PLL settings. The design of the external loop filter is crucial
to the proper operation of the PLL. A thorough knowledge of
PLL theory and design is helpful.
ADIsimCLK™ (V1.2 or later) is a free program that can help
with the design and exploration of the capabilities and features
of the AD9516, including the design of the PLL loop filter. It is
available at www.analog.com/clocks.
Phase Frequency Detector (PFD)
The PFD takes inputs from the R counter and N counter and
produces an output proportional to the phase and frequency
difference between them. The PFD includes a programmable
delay element that controls the width of the antibacklash pulse.
This pulse ensures that there is no dead zone in the PFD
transfer function and minimizes phase noise and reference
spurs. The antibacklash pulse width is set by Register 0x017[1:0].
An important limit to keep in mind is the maximum frequency
allowed into the PFD, which in turn determines the correct
antibacklash pulse setting. The antibacklash pulse setting is
specified in the phase/frequency detector parameter of Table 2.
FREQUENCY
DETECTOR
DETECT
LOCK
PHASE
CPRSET
REF
PLL
CHARGE PUMP
VCP
HOLD
LD
CP
STATUS