AD9516-3BCPZ-REEL7 Analog Devices Inc, AD9516-3BCPZ-REEL7 Datasheet - Page 59
![IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9516-3BCPZ-REEL7
Manufacturer Part Number
AD9516-3BCPZ-REEL7
Description
IC,Ten Distributed-Output Clock Driver,LLCC,64PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Clock Generator, Fanout Distributionr
Datasheet
1.AD9516-3BCPZ.pdf
(80 pages)
Specifications of AD9516-3BCPZ-REEL7
Pll
Yes
Input
Clock
Output
CMOS, LVDS, LVPECL
Number Of Circuits
1
Ratio - Input:output
1:14
Differential - Input:output
Yes/Yes
Frequency - Max
2.25GHz
Divider/multiplier
Yes/No
Voltage - Supply
3.135 V ~ 3.465 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Frequency-max
2.25GHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9516-3/PCBZ - BOARD EVAL FOR AD9516-3 2.0GHZ
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
REGISTER MAP DESCRIPTIONS
Table 53 through Table 62 provide a detailed description of each of the control register functions. The registers are listed by hexadecimal
address. A range of bits (for example, from Bit 5 through Bit 2) is indicated using a colon and brackets, as follows: [5:2].
Table 53. Serial Port Configuration
Reg.
Addr
(Hex)
0x000
0x003
0x004
Bits
[7:4]
3
2
1
0
[7:0]
0
Name
Mirrored, Bits[3:0]
Long instruction
Soft reset
LSB first
SDO active
Part ID (read only)
Read back active registers
Description
Bits[7:4] should always mirror Bits[3:0] so that it does not matter whether the part
is in MSB or LSB first mode (see Bit 1, Register 0x000). The user should set the bits as follows:
Bit 7 = Bit 0.
Bit 6 = Bit 1.
Bit 5 = Bit 2.
Bit 4 = Bit 3.
Short/long instruction mode. This part uses long instruction mode only, so this bit should
always be set to 1.
0: 8-bit instruction (short).
1: 16-bit instruction (long) (default).
Soft reset.
1: soft reset; restores default values to internal registers. Not self-clearing. Must be cleared to
0 to complete reset operation.
MSB or LSB data orientation.
0: data-oriented MSB first; addressing decrements (default).
1: data-oriented LSB first; addressing increments.
Selects unidirectional or bidirectional data transfer mode.
0: SDIO pin used for write and read; SDO set to high impedance; bidirectional mode (default).
1: SDO used for read, SDIO used for write; unidirectional mode.
Uniquely identifies the dash version (-0 through -4) of the AD9516.
AD9516-0: 0x01.
AD9516-1: 0x41.
AD9516-2: 0x81.
AD9516-3: 0x43.
AD9516-4: 0xC3.
Selects register bank used for a readback.
0: reads back buffer registers (default).
1: reads back active registers.
Rev. A | Page 59 of 80
AD9516-3