ADP1713-BL1-EVZ Analog Devices Inc, ADP1713-BL1-EVZ Datasheet
ADP1713-BL1-EVZ
Specifications of ADP1713-BL1-EVZ
Related parts for ADP1713-BL1-EVZ
ADP1713-BL1-EVZ Summary of contents
Page 1
... EN ADJ 3 4 Figure 2. ADP1712 with Adjustable Output Voltage, 0 5.0 V ADP1713 OUT 1 5 2.2µF GND BYP 4 Figure 3. ADP1713 with Fixed Output Voltage and Bypass Capacitor, 0.75 V ADP1714 OUT 1 IN OUT 5 2.2µF 2.2µF GND 2 EN TRK Figure 4. ADP1714 with Output Voltage Tracking soft-start time ...
Page 2
... REVISION HISTORY 6/09—Rev Rev. A Updated Outline Dimensions ....................................................... 15 Changes to Ordering Guide .......................................................... 15 1/07—Revision 0: Initial Version Adjustable Output Voltage (ADP1712 Adjustable) ............... 11 Bypass Capacitor (ADP1713) ................................................... 11 Track Mode (ADP1714) ............................................................ 11 Enable Feature ............................................................................ 11 Undervoltage Lockout (UVLO) ............................................... 11 Application Information ................................................................ 12 Capacitor Selection .................................................................... 12 Current Limit and Thermal Overload Protection ................. 12 Thermal Considerations ...
Page 3
... V) or 2.5 V (whichever is greater OUT Table 1. Parameter Symbol INPUT VOLTAGE RANGE V OPERATING SUPPLY CURRENT I SHUTDOWN CURRENT I FIXED OUTPUT VOLTAGE V ACCURACY (ADP1712 FIXED, ADP1713, AND ADP1714) ADJUSTABLE OUTPUT VOLTAGE V 1 ACCURACY (ADP1712 ADJUSTABLE) LINE REGULATION ∆V 2 LOAD REGULATION ∆V 3 DROPOUT VOLTAGE V 4 START-UP TIME ...
Page 4
... OUTPUT NOISE OUT ADP1713 ADP1712 and ADP1714 POWER SUPPLY REJECTION RATIO PSRR ADP1713 ADP1712 and ADP1714 1 Accuracy when OUT is connected directly to ADJ. When OUT voltage is set by external feedback resistors, absolute accuracy in adjust mode depends on the tolerances of resistors used. 2 Based on an end-point calculation using 10 mA and 300 mA loads. See 3 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage ...
Page 5
... JA Rating soldered in a circuit board for surface-mount packages. –0 –0 Table 3. Thermal Resistance –0 Package Type –0 5-Lead TSOT –65°C to +150°C –40°C to +125°C 300°C ESD CAUTION JEDEC J-STD-020 Rev Page ADP1712/ADP1713/ADP1714 θ Unit JA 170 °C/W ...
Page 6
... Track. The output follows the voltage placed on the TRK pin. (See the Theory of Operation section for a more detailed description.) 5 OUT Regulated Output Voltage. Bypass OUT to GND with a 2.2 μF or greater capacitor. Rev Page OUT ADP1713 ADP1714 GND 2 2 TOP VIEW TOP VIEW (Not to Scale) (Not to Scale) BYP EN 3 ...
Page 7
... LOAD 3.280 3.3 3.8 4.3 V (V) IN Figure 11. Output Voltage vs. Input Voltage = 2.2 μ 25°C, unless otherwise noted. A 110 100 1000 4.8 5.3 Rev Page ADP1712/ADP1713/ADP1714 450 I = 300mA LOAD 400 350 I = 200mA LOAD 300 250 I = 100mA LOAD 200 150 I = 10mA LOAD ...
Page 8
... ADP1712/ADP1713/ADP1714 180 160 140 120 100 0 (mA) LOAD Figure 15. Dropout Voltage vs. Load Current 3.35 3.30 3.25 3.20 3.15 3.10 3.05 3.00 3.20 3.25 3.30 3.35 3.40 3.45 V (V) IN Figure 16. Output Voltage vs. Input Voltage (in Dropout) 1000 900 800 700 600 500 I 400 ...
Page 9
... I = 1mA LOAD –70 – 100µA LOAD –90 10 100 1k 10k 100k FREQUENCY (Hz) Figure 22. ADP1713 Power Supply Rejection Ratio vs. Frequency (10 nF Bypass Capacitor) –50 –55 –60 –65 – Figure 23. ADP1712 Adjustable Power Supply Rejection Ratio vs. –45 – 100mA LOAD = 10mA – ...
Page 10
... V, using an internal feedback network. The adjustable output voltage can be set to between 0.8 V and 5 external voltage divider connected from OUT to ADJ. The ADP1713 and ADP1714 are available in fixed output voltage options only. The ADP1712 fixed version allows an external soft-start capacitor to be connected between the SS pin and GND, which controls the output voltage ramp during startup ...
Page 11
... R2. BYPASS CAPACITOR (ADP1713) The ADP1713 allows for an external bypass capacitor to be connected to the internal reference, which reduces output voltage noise and improves power supply rejection. A low leakage capacitor greater ( recommended) must be connected between the BYP and GND pins ...
Page 12
... Consider the case where a hard short from OUT to ground occurs. At first the ADP1712/ADP1713/ADP1714 current limit, so that only 500 mA is conducted into the short. If self heating of the junction is great enough to cause its temperature to rise above 150° ...
Page 13
... THERMAL CONSIDERATIONS To guarantee reliable operation, the junction temperature of the ADP1712/ADP1713/ADP1714 must not exceed 125°C. To ensure the junction temperature stays below this maximum value, the user needs to be aware of the parameters that contribute to junction temperature changes. These parameters include ambient temperature, power dissipation in the power device, and thermal resistances between the junction and ambient air (θ ...
Page 14
... CONSIDERATIONS Heat dissipation from the package can be improved by increasing the amount of copper attached to the pins of the ADP1712/ ADP1713/ADP1714. However, as can be seen from Table 5, a point of diminishing returns eventually is reached, beyond which an increase in the copper size does not yield significant heat dissipation benefits. ...
Page 15
... ADP1713AUJZ-0.9-R7 –40°C to +125°C 1 ADP1713AUJZ-0.95R7 –40°C to +125°C 1 ADP1713AUJZ-1.0-R7 –40°C to +125°C 1 ADP1713AUJZ-1.05R7 –40°C to +125°C 1 ADP1713AUJZ-1.1-R7 –40°C to +125°C 1 ADP1713AUJZ-1.15R7 –40°C to +125°C ADP1713AUJZ-1.2-R7 1 –40°C to +125°C 2.90 BSC 5 4 2.80 BSC ...
Page 16
... ADP1712 Fixed 3.3 V Output with Soft Start Evaluation Board Adjustable, ADP1712 Adjustable Output Evaluation Board but set to 1.6 3.3 ADP1713 Fixed 3.3 V Output with Bypass Evaluation Board 3.3 ADP1714 Fixed 3.3 V Output with Track Mode Evaluation Board D06455-0-6/09(A) D06455-0-6/09(A) Rev Page ...