ADSP-21266SKSTZ-2D Analog Devices Inc, ADSP-21266SKSTZ-2D Datasheet - Page 2

• Manufacturer Part Number: ADSP-21266SKSTZ-2D
• Description: IC,DSP,32-BIT,CMOS,QFP,144PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Fixed/Floating Pointr

Specifications of ADSP-21266SKSTZ-2D

• Interface: DAI, SPI
• Clock Rate: 200MHz
• Non-volatile Memory: ROM (512 kB)
• On-chip Ram: 256kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 144-LQFP
• Device Core Size: 32b
• Architecture: Super Harvard
• Format: Floating Point
• Clock Freq (max): 200MHz
• Mips: 200
• Device Input Clock Speed: 200MHz
• Ram Size: 256KB
• Program Memory Size: 512KB
• Operating Supply Voltage (typ): 1.2/3.3V
• Operating Supply Voltage (min): 1.14/3.13V
• Operating Supply Voltage (max): 1.26/3.47V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADSP-21266
KEY FEATURES
Serial ports offer left-justified sample-pair and I
At 200 MHz (5 ns) core instruction rate, the ADSP-21266
Super Harvard Architecture—three independent buses for
2M bits on-chip dual-ported SRAM (1M bit block 0, 1M bit
4M bits on-chip dual-ported mask-programmable ROM
Dual data address generators (DAGs) with modulo and bit-
Zero-overhead looping with single-cycle loop setup,
Single instruction multiple data (SIMD) architecture
Transfers between memory and core at up to four 32-bit
Accelerated FFT butterfly computation through a multiply
DMA controller supports:
JTAG background telemetry for enhanced emulation
IEEE 1149.1 JTAG standard test access port and on-chip
Dual voltage: 3.3 V I/O, 1.2 V core
Available in 136-ball BGA and 144-lead LQFP packages; avail-
Digital audio interface includes six serial ports, two precision
via 12 programmable and simultaneous receive or trans-
mit pins, which support up to 24 transmit or 24 receive I
channels of audio when all 6 serial ports (SPORTs) are
enabled or 6 full duplex TDM streams of up to 128
channels per frame
operates at 1200 MFLOPS peak/800 MFLOPS sustained
performance whether operating on fixed- or floating-point
data; 400 MMACS sustained performance at 200 MHz
dual data fetch, instruction fetch, and nonintrusive, zero-
overhead I/O
block 1) for simultaneous access by core processor and
DMA
(2M bits in block 0 and 2M bits in block 1)
reverse addressing
providing efficient program sequencing
provides:
Two computational processing elements
Concurrent execution—each processing element executes
Parallelism in buses and computational units allows single
floating- or fixed-point words per cycle, sustained
2.4 GBps bandwidth at 200 MHz core instruction rate; 900
Mbps is available via DMA
with add and subtract instruction
22 zero-overhead DMA channels for transfers between the
32-bit background DMA transfers at core clock speed, in
features
emulation
able in RoHS compliant packages
clock generators, an input data port, three programmable
timers, and a signal routing unit
the same instruction, but operates on different data
cycle executions (with or without SIMD) of a multiply
operation; an ALU operation; a dual memory read or
write; and an instruction fetch
ADSP-21266 internal memory and serial ports (12), the
input data ports (IDP) (eight), the SPI-compatible port
(one), and the parallel port (one)
parallel with full-speed processor execution
2
S support
Rev. C | Page 2 of 44 | October 2007
2
S
Asynchronous parallel/external port provides:
Serial ports provide:
Input data port provides an additional input path to the
Signal routing unit (SRU) provides configurable and flexible
Serial peripheral interface (SPI)
Master or slave serial boot through SPI
Full-duplex operation
Master-slave mode multimaster support
Open-drain outputs
Programmable baud rates, clock polarities, and phases
3 muxed flag/IRQ lines
1 muxed flag/timer expired line
ROM-based security features:
PLL has a wide variety of software and hardware multi-
Access to asynchronous external memory
16 multiplexed address/data lines that can support 24-bit
66M byte/sec transfer rate for 200 MHz core rate
50M byte/sec transfer rate for 150 MHz core rate
256 word page boundaries
External memory access in a dedicated DMA channel
8- to 32-bit and 16- to 32-bit word packing options
Programmable wait state options: 2 to 31 CCLKs
Six dual data line serial ports that operate at up to
Left-justified sample-pair and I
TDM support for telecommunications interfaces including
Up to 12 TDM stream support, each with 128 channels
Companding selection on a per channel basis in TDM mode
SHARC core configurable as either eight channels of I
serial data or as seven channels plus a single 20-bit wide
synchronous parallel data acquisition port
Supports receive audio channel data in I
connections between all DAI components, six serial ports,
two precision clock generators, three timers, an input data
port/parallel data acquisition port, 10 interrupts, six flag
inputs, six flag outputs, and 20 SRU I/O pins (DAI_Px)
JTAG access to memory permitted with a 64-bit key
Protected memory regions that can be assigned to limit
plier/divider ratios
address external address range with 8-bit data or 16-bit
address external address range with 16-bit data
50M bits/sec for a 200 MHz core and up to 37.5M bits/sec
for a 150 MHz core on each data line—each has a clock,
frame sync, and two data lines that can be configured as
either a receiver or transmitter pair
direction for up to 24 simultaneous receive or transmit
channels using two I
serial port
128 TDM channel support for newer telephony inter-
faces such as H.100/H.110
per frame
sample pair, or right-justified mode
access under program control to sensitive code
2
S-compatible stereo devices per
2
S support, programmable
2
S, left-justified
2
S or