EVAL-AD5272SDZ Analog Devices Inc, EVAL-AD5272SDZ Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
EVAL-AD5272SDZ
Manufacturer Part Number
EVAL-AD5272SDZ
Description
EVALUATION BOARD
Manufacturer
Analog Devices Inc
Datasheet
1.AD5274BRMZ-20.pdf
(28 pages)
Specifications of EVAL-AD5272SDZ
Main Purpose
Digital Potentiometer
Embedded
No
Utilized Ic / Part
AD5272
Primary Attributes
1 Channel, 1024 Position
Secondary Attributes
2.7 ~ 5.5 V, 5 ppm/°C, I²C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD5272/AD5274
Parameter
DYNAMIC CHARACTERISTICS
1
2
3
4
5
6
7
8
9
10
11
Table 5. AD5274 Resistor Performance Mode Code Range
Resistor Tolerance per Code
R-TOLERANCE
Table 6. AD5274 50 kΩ and 100 kΩ Resistor Performance Mode Code Range
Resistor Tolerance per Code
R-TOLERANCE
Typical specifications represent average readings at 25°C, V
Resistor position nonlinearity error (R-INL) is the deviation from an ideal value measured between the maximum resistance and the minimum resistance wiper
positions. R-DNL measures the relative step change from ideal between successive tap positions.
The maximum current in each code is defined by IAW = (V
The terms, resistor performance mode and R-Perf mode, are used interchangeably. See the Resistor Performance Mode section.
Guaranteed by design and not subject to production test.
See Figure 24 for more details.
Resistor Terminal A and Resistor Terminal W have no limitations on polarity with respect to each other. Dual-supply operation enables ground referenced bipolar
signal adjustment.
Different from operating current, the supply current for the fuse program lasts approximately 55 ms.
Different from operating current, the supply current for the fuse read lasts approximately 500 ns.
P
All dynamic characteristics use V
Bandwidth
Total Harmonic Distortion
Resistor Noise Density
1% R-Tolerance
2% R-Tolerance
3% R-Tolerance
1% R-Tolerance
2% R-Tolerance
3% R-Tolerance
DISS
is calculated from (I
DD
× V
DD
) + (I
5, 11
DD
= +2.5 V, V
SS
× V
Symbol
SS
).
SS
= −2.5 V.
DD
DD
Test Conditions/Comments
−3 dB, R
V
Code = half scale, T
|V
From 0x1E to 0xFF
From 0x0F to 0xFF
From 0x06 to 0xFF
R
From 0x1E to 0xFF
From 0x14 to 0xFF
From 0x0A to 0xFF
− 1)/R
A
AW
= 5 V, and V
DD
= 1 V rms, f = 1 kHz, code = half scale
R
R
R
R
R
R
R
R
R
= 50 kΩ
− V
AW
AW
AW
AW
AW
AW
AW
AW
AW
AW
.
AW
= 20 kΩ
= 50 kΩ
= 100 kΩ
= 20 kΩ
= 50 kΩ
= 100 kΩ
= 20 kΩ
= 50 kΩ
= 100 kΩ
SS
| = 4.5 V to 5.5 V
= 10 kΩ, Terminal W, see Figure 41
Rev. C | Page 6 of 28
SS
= 0 V.
A
= 25°C, f = 10 kHz
|V
From 0x0E to 0xFF
R
From 0x32 to 0xFF
From 0x19 to 0xFF
From 0x14 to 0xFF
From 0x0F to 0xFF
From 0x0A to 0xFF
AW
DD
= 100 kΩ
Min
− V
SS
| = 2.7 V to 4.5 V
Typ
300
120
60
−90
−88
−85
50
25
32
1
Max
Unit
kHz
dB
nV/√Hz