SI2493-C-FT Silicon Laboratories Inc, SI2493-C-FT Datasheet - Page 154
SI2493-C-FT
Manufacturer Part Number
SI2493-C-FT
Description
56 KBPS, V.92 ISOMODEM SYSTEM-SIDE - LEAD-FREE TSSOP 0 TO 7
Manufacturer
Silicon Laboratories Inc
Specifications of SI2493-C-FT
Mfg Application Notes
SI2493/57/34/15/04, Appl Note AN93
Data Format
V.21, V.22, V.23, V.29, V.32, V.34, V.90, V.92, Bell 103, Bell 212A
Baud Rates
56k
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Mounting Type
Surface Mount
Package / Case
24-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI2493-C-FT
Manufacturer:
Silicon Labs
Quantity:
135
Part Number:
SI2493-C-FTR
Manufacturer:
SIEMENS/西门子
Quantity:
20 000
- Current page: 154 of 230
- Download datasheet (7Mb)
AN93
Si2493/57/34/15/04 Layout Check List
Table 101 is a checklist that the designer can use during the layout process to ensure that all the recommendations
in this application note have been implemented. Additionally, Figure 28 provides an annotated diagram of all
relevant layout guidelines for the SI3054 CNR/AMR/ACR applications. See "3.5.19.4. Safety" on page 137 for
information about safety testing and the use of a fuse.
154
P
10
12
13
14
11
#
1
2
3
4
5
6
7
8
9
U1 and U2 are placed so that pins 9–16 of U1 are facing pins 1–8 of U2. C1 and C2 are
placed directly between U1 and U2.
Place U1, U2, C1, and C2 so that the recommended minimum creepage spacing for the
target application is implemented. R12 and R13 should be close to U1.
C1 and C2 should be placed directly between U1 and U2. Short, direct traces should be
used to connect C1 and C2 to U1 and U2. These traces should never be longer than two
inches and should be minimized in length. Place C2 such that its accompanying trace to
the C2B pin (pin 6) on the Si3018 is not close to the trace from R7 to the RNG1 pin on
the Si3018 (pin 8).
Place R7 and R8 as close as possible to the RNG1 and RNG2 pins (pins 8 and 9),
ensuring a minimum trace length from the RNG1 or RNG2 pin to the R7 or R8 resistor. In
order to space the R7 component further from the trace from C2 to the C2B pin, it is
acceptable to orient it 90 degrees relative to the RNG1 pin (pin 8).
The area of the loop from C50 to U1 pin 4 and from C51 to pin 13 back to pin 12 (DGND)
should be minimized. The return traces to U2 pin 12 (DGND) should be on the compo-
nent side.
The loop formed by XTALI, Y1, and XTALO should be minimized and routed on one
layer. The loop formed by Y1, C40, and C41 should be minimized and routed on one
layer.
The digital ground plane is made as small as possible, and the ground plane has
rounded corners.
Series resistors on clock signals are placed near source.
Use a minimum of 15 mil width traces in DAA section, use a minimum of 20 mil width
traces for IGND.
C3 should be placed across the diode bridge, and the area of the loop formed from
Si3018/19 pin 11 through C3 to the diode bridge and back to Si3018/19 pin 15 should be
minimized.
FB1, FB2, and RV1 should be placed as close as possible to the RJ11.
C8 and C9 should be placed so that there is a minimal distance between the nodes
where they connect to chassis ground.
Use at least a 20 mil wide trace from RJ11 to FB1, FB2, RV1, C8, C9, and F1.
The routing from TIP and RING of the RJ11 through F1 to the ferrite beads should be
well-matched.
Table 101. Layout Check List
Layout Items
Rev. 0.9
Required
Related parts for SI2493-C-FT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
SOIC 16/C/56 KBPS, V.92 ISOMODEM 16-PIN SYSTEM-SIDE - LEAD-FREE
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
TSSOP 24/I/56 KBPS, V.92 ISOMODEM SYSTEM-SIDE
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
Telecom ICs CONTACT SILICON LABS FOR AVAILABILITY
Manufacturer:
Silicon Laboratories Inc
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM W/ERROR CORR 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM W/ERROR CORR 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM W/DAA 16SOIC
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM SYSTEM-SIDE 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM W/ERROR CORR 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
IC ISOMODEM W/DAA 24TSSOP
Manufacturer:
Silicon Laboratories Inc
Datasheet: