162GB11E1626PE714 Amphenol PCD, 162GB11E1626PE714 Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/0/52/amphenol_pcd_sml.jpg)
162GB11E1626PE714
Manufacturer Part Number
162GB11E1626PE714
Description
Conn MIL-C-26482 Circular PIN 26 POS Crimp ST Cable Mount 26 Terminal 1 Port
Manufacturer
Amphenol PCD
Type
MIL-C-26482 Circularr
Datasheet
1.162GB10E1210PC416.pdf
(41 pages)
Specifications of 162GB11E1626PE714
Gender
RCP
Termination Method
Crimp
Mounting
Cable Mount
Body Orientation
Straight
Use Amphenol 294-542 Crimp Tool (M22520/1-01) with 294-1889-
01 Turret Head (M22520/1-02). Release and rotate Turret Knob to
proper contact size (as per colour code) and lock adjust Selector
Knob on handle to correct wire size [see table].
Insert stripped wire into Contact Pocket until it is visible through
inspection hole. Fully seat Contact in Crimp Tool Positioner and
close handles in one full stroke. (The Ratchet will not release until
tool has completed full stroke).
through Inspection Hole.
WIRE STRIPPING – 162GB SERIES
Strip 5.6mm (.220 in) to 6.6mm (.260 in) of insulation from end
of wire for both size 20 and 16 contacts taking care not to cut or
nick strands. If ends fray twist them back to their original lay.
CONTACT AND WIRE DATA – 162GB SERIES
CRIMP WIRE CONTACTS
CRIMPING WIRE TO CONTACT
CONTACT INSERTION
Select the proper insertion tool for the size of contact Table
1. The Insertion Tool and procedure are the same for both
pin and socket contacts. Slide rear accessory and sleeve
over wire bundle. Lay wire in groove of insertion tool and
slide contact into front of tool until it is properly located in
tool probe. Insert contact into the correct hole in the rear
face of the grommet. Keeping contact in line with the axis
of the hole, apply a smooth even push on the tool until the
contact is fully seated in position. Note: it is essential that
the contact and tool are correctly aligned with the axis of
hole during insertion to prevent damage to contacts.
Withdraw tool at right angles to grommet surface until
complete free of connector. All contacts must be inserted
whether in circuit or not and the appropriate size sealing
plug used behind any contacts that are not wired. Push
the sealing plug in by hand until it is fully seated.
Contact
Size
20
16
I
Colour
NSPECTION HOLE
Code
BLUE
RED
Pin: 162GB-149-20000-05
Skt: 162GB-101-20000-05
Pin: 162GB-149-16000-05
Skt: 162GB-101-16000-05
Contact Part Nos
Inspect Crimp for wire visibility
20, 22, 24
16, 18, 20
A.W.G.
Suitable Wire Sizes
Contact
Size
20
16
Colour
BLUE
Code
RED
0.032 – 0.020
0.051 – 0.032
1.295 – 0.81
0.81-0.51
in mm
CRIMPING JAW SETTING
Contact Size
294GB-5000-20
Amphenol
Assembly Instructions
294-96
20
16
Insertion Tool Part No.
O.D. range for Grommet
Permissible Insulation
TABLE 1
0.047 – 0.085
0.066 – 0.109
1.675 – 2.77
1.19 - 2.16
Sealing
MS 24256A-16
Wire Size
24
22
20
20
18
16
M.S.
-
Crimp Jaw Setting
Grommet Sealing
162GB-130-20000
162GB-130-16000
162GB
0.220 – 0.260
0.220-0.260
Stripping
Lengths
5.6 – 6.6
5.6 - 6.6
No. 2
No. 4
No. 5
No. 6
No.3
No.4
in mm
Plug
40