BFC247086334 Vishay, BFC247086334 Datasheet - Page 11

• Manufacturer Part Number: BFC247086334
• Description: Cap Film 0.33uF 100VDC/63VAC PET 5% 7.2 X 6 X 11mm RDL 5mm Ammo Pack
• Manufacturer: Vishay
• Series: 2222470r

Specifications of BFC247086334

• Package/case: 7.2(Max) X 6(Max) X 11(Max)
• Mounting: Through Hole
• Capacitance Value: 0.33 uF
• Voltage: 100|63 Vdc|Vac
• Dielectric: PET
• Lead Pitch For Radial: 5 mm
• Product Length: 7.2(Max) mm
• Product Depth: 6(Max) mm
• Tolerance: 5 %
• Operating Temperature: -55 to 125 °C
• Capacitance: 0.33UF
• Voltage Rating, Ac: 63V
• Voltage Rating, Dc: 100V
• Capacitor Dielectric Type: POLYESTER
• Tolerance,: 5%
• Tolerance, -: 5%
• Temp, Op. Max: 125(DEGREE C)
• Rohs Compliant: YES

INSPECTION REQUIREMENTS
General Notes:
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-2 and
Specific Reference Data”.
Group C Inspection Requirements
Document Number: 28112
Revision: 26-Apr-11
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
SUB-CLAUSE NUMBER AND TEST
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1
4.3.1
4.3
4.4
4.14
4.4.2
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
4.6.1
4.6
4.7
4.7.2
Dimensions (detail)
Initial measurements
Robustness of terminations
Resistance to soldering heat
Component solvent resistance
Final measurements
Initial measurements
Rapid change of temperature
Vibration
Final inspection
Metallized Polyester Film Capacitors
This document is subject to change without notice.
For technical questions, contact:
CONDITIONS
Capacitance
Tangent of loss angle for:
Tensile: Load 10 N; 10 s
Bending: Load 5 N; 4 x 90°
Method: 1A
Isopropylalcohol at room temperature
Method: 2
Visual examination
Capacitance
Tangent of loss angle
Capacitance
Tangent of loss angle for:
A = - 55 °C
B = + 125 °C
5 cycles
Duration t = 30 min
Visual examination
Mounting:
See section “Mounting” of this specification
Procedure B4
Visual examination
MKT Radial Potted Type
C  10 nF at 1 MHz
10 nF < C  470 nF at 100 kHz
C > 470 nF at 10 kHz
Solder bath: 280 °C ± 5 °C
Duration: 10 s
Immersion time: 5 min ± 0.5 min
Recovery time: Min. 1 h, max. 2 h
C  10 nF at 1 MHz
10 nF < C  470 nF at 100 kHz
C > 470 nF at 10 kHz
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s²
(whichever is less severe)
Total duration 6 h
[e-mail]
PERFORMANCE REQUIREMENTS
As specified in chapters “General Data” of this
specification
No visible damage
No visible damage
Legible marking
C/C|  2 % of the value measured initially
Increase of tan 
Compared to values measured in 4.3.1
No visible damage
No visible damage
 0.005 for: C  10 nF or
 0.003 for: 10 nF < C  470 nF or
 0.002 for: C > 470 nF
Vishay BCcomponents
www.vishay.com/doc?91000
MKT470
www.vishay.com
11