NSK70721PE.C2 Intel, NSK70721PE.C2 Datasheet - Page 14
NSK70721PE.C2
Manufacturer Part Number
NSK70721PE.C2
Description
Manufacturer
Intel
Datasheet
1.NSK70721PE.C2.pdf
(82 pages)
Specifications of NSK70721PE.C2
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (min)
4.75V
Operating Supply Voltage (max)
5.25V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
28
Lead Free Status / RoHS Status
Supplier Unconfirmed
- Current page: 14 of 82
- Download datasheet (2Mb)
SK70725/SK70721 — Enhanced Multi-Rate DSL Data Pump Chip Set
14
Control Mode
1. This input is a Schmidt Triggered circuit and includes an internal pull-up device.
2. This input is a Schmidt Triggered circuit and includes an internal pull-down device.
3. This input includes an internal pull-up device.
4. This input includes an internal pull-down device.
5. I/O column entries: DI = Digital Input; DO = Digital Output; DI/O = Digital Input/Output; AI = Analog Input; AO = Analog Output;
Description
(Hardware
Hardware
Interface
AI/O = Analog Input/Output; S = Supply.
Group
Signal
Table 2.
only)
Pin #
EDSP Pin Assignments/Signal Descriptions (Continued)
4
5
6
9
ACTREQ
ACTVNG
LOOPID
Symbol
QUIET
DI
I/O
DI
DI
DO
2
/O
2
2
5
Quiet Mode Enable. Set high to force the EDSP into the Deactivated state. Set
low to enable activation requests (see ACTREQ).
Activation Request (Master mode only - not used in Slave mode). When
QUIET is low, a rising edge on this pin initiates activation. The signal is ignored
after activation. In Slave mode this pin may be held low or left open.
Loop Number Control (Master mode) or Loop Number Indicator (Slave
mode). This indicator is transmitted from the Master to the Slave and can be
used for loop identification in systems that multiplex data onto two MDSL lines.
In Slave mode LOOPID is valid only when in the ACTIVE state. LOOPID=0
identifies MDSL loop 1 in accordance with the ETSI standard. LOOPID must be
set before the Master is activated. LOOPID may be originated in the EMDP only
when operating in modes 6 or 7.
Activating State Indication. ACTVNG is high when the EMDP is in the
Activating state.
Description
Datasheet
Related parts for NSK70721PE.C2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel Strataflash Memory28F128J3 28F640J3 28F320J3
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Controllers, Intel 430TX PCIset: 82439TX System Controller (MTXC)
Manufacturer:
Intel Corporation