PIC18LF26J53-I/SP Microchip Technology, PIC18LF26J53-I/SP Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC18LF26J53-I/SP
Manufacturer Part Number
PIC18LF26J53-I/SP
Description
28-pin, USB, 64KB Flash, 4KB RAM, 12 MIPS, 12-bit ADC 28 SPDIP .300in TUBE
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC18F26J13-ISS.pdf
(496 pages)
2.PIC18F26J53-ISS.pdf
(586 pages)
3.PIC18F26J53-ISS.pdf
(12 pages)
Specifications of PIC18LF26J53-I/SP
Core Processor
PIC
Core Size
8-Bit
Speed
48MHz
Connectivity
I²C, LIN, SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
64KB (32K x 16)
Program Memory Type
FLASH
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 2.75 V
Data Converters
A/D 10x10b/12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
2.4.1
In recent years, large value, low-voltage, surface
mount ceramic capacitors have become very cost
effective in sizes up to a few tens of microfarad. The
low-ESR, small physical size and other properties
make ceramic capacitors very attractive in many types
of applications.
Ceramic capacitors are suitable for use with the
internal voltage regulator of this microcontroller. How-
ever, some care is needed in selecting the capacitor to
ensure that it maintains sufficient capacitance over the
intended operating range of the application.
Typical low-cost, 10 µF ceramic capacitors are avail-
able in X5R, X7R and Y5V dielectric ratings (other
types are also available, but are less common). The
initial tolerance specifications for these types of capac-
itors are often specified as ±10% to ±20% (X5R and
X7R), or -20%/+80% (Y5V). However, the effective
capacitance that these capacitors provide in an
application circuit will also vary based on additional
factors, such as the applied DC bias voltage and the
temperature. The total in-circuit tolerance is, therefore,
much wider than the initial tolerance specification.
The X5R and X7R capacitors typically exhibit satisfac-
tory temperature stability (ex: ±15% over a wide
temperature range, but consult the manufacturer's data
sheets for exact specifications). However, Y5V capaci-
tors typically have extreme temperature tolerance
specifications of +22%/-82%. Due to the extreme
temperature tolerance, a 10 µF nominal rated Y5V type
capacitor may not deliver enough total capacitance to
meet minimum internal voltage regulator stability and
transient response requirements. Therefore, Y5V
capacitors are not recommended for use with the
internal voltage regulator if the application must
operate over a wide temperature range.
In addition to temperature tolerance, the effective
capacitance of large value ceramic capacitors can vary
substantially, based on the amount of DC voltage
applied to the capacitor. This effect can be very signifi-
cant, but is often overlooked or is not always
documented.
A typical DC bias voltage vs. capacitance graph for
16V, 10V and 6.3V rated capacitors is shown in
Figure
2010 Microchip Technology Inc.
2-4.
CONSIDERATIONS FOR CERAMIC
CAPACITORS
PIC18F47J53 FAMILY
FIGURE 2-4
When selecting a ceramic capacitor to be used with the
internal voltage regulator, it is suggested to select a
high-voltage rating, so that the operating voltage is a
small percentage of the maximum rated capacitor volt-
age. For example, choose a ceramic capacitor rated at
16V for the 2.5V core voltage. Suggested capacitors
are shown in
2. Module: Reset
Table 5-2 incorrectly defines the SSP2STAT Reset
state as ‘1111 1111’. The correct Reset state of the
SSP2STAT is ‘0000 0000’.
This correction also applies to all other occurrences of
this value throughout the device data sheet, including:
• Table 6-4: Register File Summary (PIC18F47J53)
• Register 20-1: SSPxSTAT: MSSPx Status
• Register 20-5: SSPxSTAT: MSSPx Status
3. Module: Device Overview
Figures 1-1 and 1-2 incorrectly denote the program
memory size as being 16 Kbytes to 64 Kbytes. The
correct program memory size is 64 Kbytes to
128 Kbytes.
Register (SPI Mode) (Access 1, FC7h; 2, F73h;
2 F73h)
Register (I
-10
-20
-30
-40
-50
-60
-70
-80
10
0
0
6.3V Capacitor
1
2
2
Table
3
C™ Mode) (1, Access FC7h; 2, F73h)
4
DC Bias Voltage (VDC)
5
2-1.
6
10V Capacitor
DC BIAS VOLTAGE vs.
CAPACITANCE
CHARACTERISTICS
7
8
9
10
16V Capacitor
11
DS80506C-page 7
12
13
14
15
16
17