7902401JA E2V, 7902401JA Datasheet - Page 3

• Manufacturer Part Number: 7902401JA
• Manufacturer: E2V

Specifications of 7902401JA

• Lead Free Status / RoHS Status: Supplier Unconfirmed

DSCC FORM 2234
APR 97
the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
this drawing shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing
(QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535
may be processed as QML product in accordance with the manufacturer's approved program plan and qualifying activity
approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make
modifications to the requirements herein. These modifications shall not affect the PIN as described herein. A "Q" or "QML"
certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used.
MIL-PRF-38535, appendix A and herein.
for unprogrammed devices for contracts involving no altered item drawing. When testing is required per 4.3 herein, the devices
shall be programmed by the manufacturer prior to test in a checkerboard pattern (a minimum of 50 percent of the total number of
bits programmed) or to any altered item drawing pattern which includes at least 25 percent of the total number of bits
programmed.
as specified in table I and shall apply over the full case operating temperature range.
tests for each subgroup are described in table I.
in 1.2 herein. In addition, the manufacturer's PIN may also be marked.
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
3.1 Item requirements The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
3.2.1 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.2 Unprogrammed devices. Testing to the applicable truth table, or alternate testing as specified in 4.3.1d, shall be used
3.2.3 Programmed devices. The truth table for programmed devices shall be specified by an altered item drawing.
3.2.4 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3. REQUIREMENTS
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
(Copies of these documents are available online at
DEFENSE SUPPLY CENTER COLUMBUS
DEPARTMENT OF DEFENSE SPECIFICATION
DEPARTMENT OF DEFENSE STANDARDS
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
MIL-STD-883
MIL-STD-1835 -
MIL-HDBK-103 -
MIL-HDBK-780 -
COLUMBUS, OHIO 43218-3990
MICROCIRCUIT DRAWING
-
STANDARD
Interface Standard Electronic Component Case Outlines.
Standard Microcircuit Drawings.
Test Method Standard Microcircuits.
List of Standard Microcircuit Drawings.
http://assist.daps.dla.mil/quicksearch/
SIZE
A
REVISION LEVEL
or
C
http://assist.daps.dla.mil
SHEET
79024
3
or from