SY69753LHI Micrel Inc, SY69753LHI Datasheet - Page 3
![IC CLOCK/DATA REC 155MBPS 32TQFP](/photos/6/50/65003/576-32-epad-tqfp_sml.jpg)
SY69753LHI
Manufacturer Part Number
SY69753LHI
Description
IC CLOCK/DATA REC 155MBPS 32TQFP
Manufacturer
Micrel Inc
Type
Clock and Data Recovery (CDR)r
Datasheet
1.SY69753LHG.pdf
(13 pages)
Specifications of SY69753LHI
Input
PECL, TTL
Output
PECL, TTL
Frequency - Max
1.25GHz
Voltage - Supply
3.15 V ~ 3.45 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-TQFP Exposed Pad, 32-eTQFP, 32-HTQFP, 32-VQFP
Frequency-max
1.25GHz
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SY69753LHI
Manufacturer:
MICROEL
Quantity:
5 510
Company:
Part Number:
SY69753LHI
Manufacturer:
NEC
Quantity:
5 510
Pin Description
Inputs
Outputs
Power and Ground
Note:
1. VCC, VCCA, VCCO must be the same value.
December 2007
Pin Number
Pin Number
Pin Number
1, 4, 6, 7, 8
27, 28
29, 30
19, 22
12, 13
26
32
25
16
31
23
24
20
21
18
17
10
14
15
11
2
3
5
9
Pin Name
Pin Name
Pin Name
RDOUTN
RDOUTP
DIVSEL1
DIVSEL2
REFCLK
CLKSEL
RCLKN
RCLKP
TCLKP
TCLKN
PLLRN
RDINP
RDINN
PLLSP
PLLSN
PLLRP
VCCO
GNDA
VCCA
GND
LFIN
VCC
CD
NC
Differential
Differential
Differential
Differential
TTL Input
TTL Input
TTL Input
Output
PECL
PECL
PECL
PECL
PECL
Type
Type
Type
Input
TTL
Pin Name
Serial Data Input: These built-in line receiver inputs are connected to the differential
receive serial data stream. An internal receive PLL recovers the embedded clock
(RCLK) and data (RDOUT) information.
Reference Clock: This input is used as the reference for the internal frequency
synthesizer and the "training" frequency for the receiver PLL to keep it centered in the
absence of data coming in on the RDIN inputs.
Carrier Detect: This input controls the recovery function of the Receive PLL and can be
driven by the carrier detect output of optical modules or from external transition
detection circuitry. When this input is HIGH, the input data stream (RDIN) is recovered
normally by the Receive PLL. When this input is LOW the data on the inputs RDIN will
be internally forced to a constant LOW, the data outputs RDOUT will remain LOW, the
Link Fault Indicator output LFIN forced LOW and the clock recovery PLL forced to look
onto the clock frequency generated from REFCLK.
Divider Select: These inputs select the ratio between the output clock frequency
(RCLK/TCLK) and the REFCLK input frequency as shown in the “Reference Frequency
Selection” table.
Clock Select: This input is used to select either the recovered clock of the receiver PLL
(CLKSEL = HIGH) or the clock of the frequency synthesizer (CLKSEL = LOW) to the
TCLK outputs.
Pin Name
Link Fault Indicator: This output indicates the status of the input data stream RDIN.
Active HIGH signal is indicating when the internal clock recovery PLL has locked onto
the incoming data stream. LFIN will go HIGH if CD is HIGH and RDIN is within the
frequency range of the Receive PLL (1000ppm) and will be alternating if not. LFIN is an
asynchronous output.
Receive Data Output: These ECL 100K outputs represent the recovered data from the
input data stream (RDIN). This recovered data is specified against the rising edge of
RCLK.
Clock Output: These ECL 100K outputs represent the recovered clock used to sample
the recovered data (RDOUT).
Clock Output: These ECL 100K outputs represent either the recovered clock (CLKSEL
= HIGH) used to sample the recovered data (RDOUT) or the transmit clock of the
frequency synthesizer (CLKSEL = LOW).
Clock Synthesis PLL Loop Filter: External loop filter pins for the clock synthesis PLL.
Clock Recovery PLL Loop Filter: External loop filter pins for the receiver PLL.
Pin Name
Power Supply.
Analog Power Supply Voltage.
Output Supply Voltage.
Ground.
No connect.
Analog Ground.
(1)
(1)
3
(1)
hbwhelp@micrel.com
or (408) 955-1690
M9999-120307-F