4-179228-3 TE Connectivity, 4-179228-3 Datasheet
![CT CRIMP-2 REC HSG 3P YELLOW](/photos/41/48/414808/pr35894004c_sml.jpg)
4-179228-3
Specifications of 4-179228-3
Available stocks
Related parts for 4-179228-3
4-179228-3 Summary of contents
Page 1
... MIL-STD-202: Test Methods for Electronic and Electrical Component Parts. B REVISED FB00-0158-04 A2 REVISED FJ00-0250-00 DIST LTR REVISION RECORD ASHL-0004-ES REV A Product Specification 108-5408 AMP Common Termination (CT), Connector 2mm Pitch, Crimp Type II Receptacle Housing, 2-15 Pos. Receptacle Contact (Strip Terminal) Applicable Wire: AWG #22~26 Receptacle Contact (Loose Piece) ...
Page 2
... Nickel underplate) : 6/6 Nylon (UL94 V-0) : Pretin lead Brass (0.8um min. thick solder-plated over 0.5um min. thick copper underplate) : 6/6 Nylon GF Type (UL94 V-0) : Pretin lead Brass (0.8um min. thick solder-plated over 0.5um min. thick copper underplate) : 6/6 Nylon (UL94 V-0) : Brass (0 ...
Page 3
... The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig.2, Para. 3.8. All tests shall be performed at ambient temperature unless otherwise specified. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B : 125 V(AC/DC #22 AWG 3A #24 AWG 2.5A #26 AWG 1.5A #28 AWG 1A #30 AWG o o ...
Page 4
... AWG 29 AWG 19 AWG 14 AWG 9.8 14.7N Max. 14.7N Min. per contact. 14.7N Min. per contact. Fig. 2 (To be continued) PAGE Procedures Subject terminated connector and header to mate and unmate to measure the force required to engage and disengage by operating the head at a rate of 4 ...
Page 5
... ASHL-0005- ES REV B Requirements 49.0N Max. 83.3N Min. Product shall be confirming to the requirements of applicable product drawing and Application Specification 114-5179. Electrical Performance Requirements 10 m Max. (Initial Max. (Final) Connector must withstand test potential of 1.0 kV (AC) for 1 minute. Current leakage must be 5.0mA Max. ...
Page 6
... C for 48 hours. Subsequent measurement shall be done after reconditioning in the room temperature for 1 hour. Subject mated connectors to steady state humidity at 40 and 90~95 % R.H. MIL-STD-202, Method 103, Condition B. Subject mated connectors cycles between -55 C and 85 for 30 minutes each duration at temperature extremes ...
Page 7
... Fig. 2 (End) PAGE Procedures Subject mated connectors to sulfurous acid gas atmosphere of 3±1ppm concentration at o 40±2 C for 240 hours. Subsequent measurement shall be done after reconditioning in the room temperature for 1 hour. Subject contacts to solderability testing, as specified. MIL-STD-202, Method 208. Subject product mounted on ...
Page 8
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig.3 Fig.4 Fig.5 Fig.7 PAGE Fig.6 Document No. REV 108-5408 LOC B ES ...
Page 9
... Test Specimens: The test specimens to be used for the performance evaluation testing, shall be prepared in accordance with AMP Application Specification, 114-5179, Termination of AMP CT Connector Pitch, Crimp Type II, by using the samples selected from the current production at random, and conforming to the requirements of the applicable product drawing. ...
Page 10
... Post Header, Vertical (V), Short Tine, Box Type X-175489-X Post Header, Horizontal (H), Box Type X-175661-X Post Header, Horizontal (H), Box Type, in Tube X-176394-X Post Header, Horizontal (H), Gold-plated Contact, Box Type X-177626-X Post Header, Horizontal (H), Short Tine, Box Type X-175694-X Post Header, w/Panel Lock, for Relay Tyco Electronics AMP Shanghai Ltd ...
Page 11
... Post Header, Vertical (V), SMT Type, Box Type, on Embossment Tape Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Product Descriptions Appendix 1 PAGE No. of Pos. 2~6, 8 Pos. 2~6, 8 Pos. 2~6, 8 Pos 8~11 Pos. 7~10, 13 Pos. Document No. REV 108-5408 2~5 Pos. 6 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 3 Pos. ...