LTC2208IUP#TR Linear Technology, LTC2208IUP#TR Datasheet - Page 15
![IC ADC 16BIT 130MSPS 64-QFN](/photos/6/63/66316/64-qfn_05-08-1705_sml.jpg)
LTC2208IUP#TR
Manufacturer Part Number
LTC2208IUP#TR
Description
IC ADC 16BIT 130MSPS 64-QFN
Manufacturer
Linear Technology
Datasheet
1.LTC2208CUPPBF.pdf
(32 pages)
Specifications of LTC2208IUP#TR
Number Of Bits
16
Sampling Rate (per Second)
130M
Data Interface
Parallel
Number Of Converters
1
Power Dissipation (max)
1.78W
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-WFQFN, Exposed Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PIN FUNCTIONS
For LVDS Mode. STANDARD or LOW POWER
SENSE (Pin 1): Reference Mode Select and External
Reference Input. Tie SENSE to V
2.5V bandgap reference. An external reference of 2.5V or
1.25V may be used; both reference values will set a full
scale ADC range of 2.25V (PGA = 0).
GND (Pins 2, 4, 7, 10, 11, 14, 18): ADC Power Ground.
V
mon mode. Must be bypassed to ground with a minimum
of 2.2μF . Ceramic chip capacitors are recommended.
V
Bypass to GND with 1μF ceramic chip capacitors.
A
A
ENC
sampled analog input is held on the rising edge of ENC
Internally biased to 1.6V through a 6.2k resistor. Output
data can be latched on the rising edge of ENC
ENC
sampled analog input is held on the falling edge of ENC
Internally biased to 1.6V through a 6.2k resistor. Bypass to
ground with a 0.1μF capacitor for a single-ended Encode
signal.
SHDN (Pin 19): Power Shutdown Pin. SHDN = low results
in normal operation. SHDN = high results in powered
down analog circuitry and the digital outputs are set in
high impedance state.
DITH (Pin 20): Internal Dither Enable Pin. DITH = low
disables internal dither. DITH = high enables internal dither.
Refer to Internal Dither section of the data sheet for details
on dither operation.
D0
51-58): LVDS Digital Outputs. All LVDS outputs require
differential 100Ω termination resistors at the LVDS receiver.
D15
CM
DD
IN
IN
–
+
–
/D0
+
(Pin 3): 1.25V Output. Optimum voltage for input com-
+
–
(Pins 5, 6, 15, 16, 17): 3.3V Analog Supply Pin.
(Pin 8): Positive Differential Analog Input.
(Pin 9): Negative Differential Analog Input.
/D15
(Pin 13): Negative Differential Encode Input. The
(Pin 12): Positive Differential Encode Input. The
+
to D15
–
is the MSB.
–
/D15
+
(Pins 21-30, 33-38, 41-48 and
DD
to select the internal
+
.
+
–
.
.
OGND (Pins 31 and 50): Output Driver Ground.
OV
Drivers. Bypass to ground with 0.1μF capacitor.
CLKOUT
0utput. Latch data on the rising edge of CLKOUT
edge of CLKOUT
OF
OF is high when an over or under fl ow has occurred.
LVDS (Pin 61): Data Output Mode Select Pin. Connecting
LVDS to 0V selects full rate CMOS mode. Connecting LVDS
to 1/3V
LVDS to 2/3V
ing LVDS to V
MODE (Pin 62): Output Format and Clock Duty Cycle
Stabilizer Selection Pin. Connecting MODE to 0V selects
offset binary output format and disables the clock duty
cycle stabilizer. Connecting MODE to 1/3V
binary output format and enables the clock duty cycle sta-
bilizer. Connecting MODE to 2/3V
output format and enables the clock duty cycle stabilizer.
Connecting MODE to V
format and disables the clock duty cycle stabilizer.
RAND (Pin 63): Digital Output Randomization Selection Pin.
RAND low results in normal operation. RAND high selects
D1-D15 to be EXCLUSIVE-ORed with D0 (the LSB). The
output can be decoded by again applying an XOR operation
between the LSB and all other bits. The mode of operation
reduces the effects of digital output interference.
PGA (Pin 64): Programmable Gain Amplifi er Control Pin. Low
selects a front-end gain of 1, input range of 2.25V
selects a front-end gain of 1.5, input range of 1.5V
GND (Exposed Pad Pin 65): ADC Power Ground. The
exposed pad on the bottom of the package must be sol-
dered to ground.
–
DD
/OF
(Pins 32 and 49): Positive Supply for the Output
DD
+
–
(Pins 59 and 60): Over/Under Flow Digital Output
/CLKOUT
selects demultiplexed CMOS mode. Connecting
DD
DD
selects Low Power LVDS mode. Connect-
–
selects Standard LVDS mode.
.
+
(Pins 39 and 40): LVDS Data Valid
DD
selects 2’s complement output
DD
selects 2’s complement
LTC2208
DD
selects offset
P-P
+
15
, falling
. High
P-P
2208fc
.