KAD5512P-17Q72 Intersil, KAD5512P-17Q72 Datasheet - Page 25
![IC ADC 12BIT 170MSPS SGL 72-QFN](/photos/28/17/281743/72-vfqfn_l72d_sml.jpg)
KAD5512P-17Q72
Manufacturer Part Number
KAD5512P-17Q72
Description
IC ADC 12BIT 170MSPS SGL 72-QFN
Manufacturer
Intersil
Series
FemtoCharge™r
Datasheet
1.KAD5512P-25Q72.pdf
(36 pages)
Specifications of KAD5512P-17Q72
Number Of Bits
12
Sampling Rate (per Second)
170M
Data Interface
Serial, SPI™
Number Of Converters
1
Power Dissipation (max)
253mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
72-VFQFN Exposed Pad
For Use With
KDC5512EVAL - DAUGHTER CARD FOR KAD5512
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Bit 7 SDO Active
Bit 6 LSB First
Bit 5 Soft Reset
Bit 4 Reserved
Bits 3:0 These bits should always mirror bits 4:7 to
avoid ambiguity in bit ordering.
ADDRESS 0X02: BURST_END
If a series of sequential registers are to be set, burst
mode can improve throughput by eliminating redundant
addressing. In 3-wire SPI mode the burst is ended by
pulling the CSB pin high. If the device is operated in 2-
wire mode the CSB pin is not available. In that case,
setting the burst_end address determines the end of the
transfer. During a write operation, the user must be
cautious to transmit the correct number of bytes based
on the starting and ending addresses.
Bits 7:0 Burst End Address
Device Information
ADDRESS 0X08: CHIP_ID
ADDRESS 0X09: CHIP_VERSION
The generic die identifier and a revision number,
respectively, can be read from these two registers.
Indexed Device Configuration/Control
ADDRESS 0X10: DEVICE_INDEX_A
A common SPI map, which can accommodate
single-channel or multi-channel devices, is used for all
Intersil ADC products. Certain configuration commands
(identified as Indexed in the SPI map) can be executed
on a per-converter basis. This register determines which
converter is being addressed for an Indexed command. It
is important to note that only a single converter can be
addressed at a time.
This register defaults to 00h, indicating that no ADC is
addressed. Therefore Bit 0 must be set high in order to
execute any Indexed commands. Error code ‘AD’ is
returned if any indexed register is read from without
properly setting device_index_A.
ADDRESS 0X20: OFFSET_COARSE AND
ADDRESS 0X21: OFFSET_FINE
The input offset of the ADC core can be adjusted in fine
and coarse steps. Both adjustments are made via an 8-
bit word as detailed in Table 7.
Setting this bit high configures the SPI to interpret
serial data as arriving in LSB to MSB order.
Setting this bit high resets all SPI registers to default
values.
This bit should always be set high.
This register value determines the ending address of
the burst data.
25
KAD5512P
The default value of each register will be the result of the
self-calibration after initial power-up. If a register is to be
incremented or decremented, the user should first read
the register value then write the incremented or
decremented value back to the same register.
ADDRESS 0X22: GAIN_COARSE
ADDRESS 0X23: GAIN_MEDIUM
ADDRESS 0X24: GAIN_FINE
Gain of the ADC core can be adjusted in coarse,
medium and fine steps. Coarse gain is a 4-bit
adjustment while medium and fine are 8-bit. Multiple
Coarse Gain Bits can be set for a total adjustment
range of ±4.2% (‘0011’ =~ -4.2% and
‘1100’ =~ +4.2%). It is recommended to use one of
the coarse gain settings (-4.2%, -2.8%, -1.4%, 0,
1.4%, 2.8%, 4.2%) and fine-tune the gain using the
registers at 23h and 24h.
The default value of each register will be the result of the
self-calibration after initial power-up. If a register is to be
incremented or decremented, the user should first read
the register value then write the incremented or
decremented value back to the same register.
+Full Scale (0xFF)
–Full Scale (0x00) -133LSB (-47mV)
Nominal Step Size 1.04LSB (0.37mV)
Mid–Scale (0x80)
–Full Scale (0x00)
+Full Scale (0xFF)
Nominal Step Size
Mid–Scale (0x80)
PARAMETER
TABLE 9. MEDIUM AND FINE GAIN ADJUSTMENTS
PARAMETER
0x22[3:0]
Steps
Steps
Bit3
Bit2
Bit1
Bit0
TABLE 8. COARSE GAIN ADJUSTMENT
TABLE 7. OFFSET ADJUSTMENTS
COARSE OFFSET
0.0LSB (0.0mV)
MEDIUM GAIN
NOMINAL COARSE GAIN ADJUST
0x20[7:0]
+133LSB
(+47mV)
0x23[7:0]
0.016%
0.00%
255
+2%
-2%
256
+2.8
+1.4
(%)
-2.8
-1.4
+5LSB (+1.75mV)
-5LSB (-1.75mV)
FINE OFFSET
0x21[7:0]
(0.014mV)
0.04LSB
FINE GAIN
0x24[7:0]
0.0LSB
0.0016%
255
-0.20%
+0.2%
0.00%
October 1, 2010
256
FN6807.4