AD5415YRU Analog Devices Inc, AD5415YRU Datasheet - Page 15

• Manufacturer Part Number: AD5415YRU
• Description: IC DAC DUAL 12BIT MULT 24-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5415YRU

• Settling Time: 120ns
• Number Of Bits: 12
• Data Interface: Serial
• Number Of Converters: 2
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 3.5µW
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP
• For Use With: EVAL-AD5415EBZ - BOARD EVALUATION FOR AD5415
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

GENERAL DESCRIPTION
DAC SECTION
The AD5415 is a 12-bit, dual-channel, current output DAC
consisting of standard inverting R-2R ladder configuration.
Figure 33 shows a simplified diagram of a single channel of the
AD5415. The feedback resistor R
of R is typically 10 kΩ (with a minimum of 8 kΩ and a
maximum of 12 kΩ). If I
potential, a constant current flows into each ladder leg,
regardless of the digital input code. Therefore, the input
resistance presented at V
Access is provided to the V
the DAC, making the device extremely versatile and allowing it
to be configured in several operating modes, such as unipolar
output, bipolar output, or single-supply mode.
CIRCUIT OPERATION
Unipolar Mode
Using a single op amp, this device can easily be configured to
provide 2-quadrant multiplying operation or a unipolar output
voltage swing, as shown in Figure 34.
V
REF
A
2R
S1
R
DAC DATA LATCHES
AND DRIVERS
2R
Figure 33. Simplified Ladder
S2
R
OUT
REF
2R
S3
REF
1 and I
is always constant.
, R
AGND
NOTES
1. DAC B OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
FB
R
FB
IF A1 IS A HIGH SPEED AMPLIFIER.
, I
OUT
R2_3A
has a value of 2R. The value
OUT
R2A
R3A
2R
2 are kept at the same
S12
1, and I
V
2R
DD
V
REF
R3
2R
R2
2R
OUT
R
R1A
A
2 terminals of
R
I
I
OUT
OUT
SYNC
FB
R1
2R
μCONTROLLER
A
12-BIT DAC A
Figure 34. Unipolar Operation
1A
2A
AD5415
SCLK
Rev. B | Page 15 of 32
R
R
2R
FB
SDIN
AGND
GND
I
I
OUT
OUT
R
When an output amplifier is connected in unipolar mode, the
output voltage is given by
where:
D is the fractional representation, in the range of 0 to 4,095, of
the digital word loaded to the DAC.
n is the number of bits.
Note that the output voltage polarity is opposite the V
polarity for dc reference voltages. This DAC is designed to
operate with either negative or positive reference voltages. The
V
the on and off states of the DAC switches.
This DAC is also designed to accommodate ac reference input
signals in the range of −10 V to +10 V.
With a fixed 10 V reference, the circuit in Figure 34 gives a
unipolar 0 V to −10 V output voltage swing. When V
ac signal, the circuit performs 2-quadrant multiplication.
Table 5 shows the relationship between digital code and
expected output voltage for unipolar operation.
Table 5. Unipolar Code
Digital Input
1111 1111 1111
1000 0000 0000
0000 0000 0001
0000 0000 0000
FB
DD
1A
2A
A
power pin is only used by the internal digital logic to drive
V
AGND
OUT
C1
= − V
A1
REF
V
OUT
× D /2
= 0V TO –V
n
IN
Analog Output (V)
−V
−V
−V
−V
REF
REF
REF
REF
(4,095/4,096)
(2,048/4,096) = −V
(1/4,096)
(0/4,096) = 0
AD5415
IN
REF
is an
REF
/2