EP3SL150F1152C3N Altera, EP3SL150F1152C3N Datasheet - Page 23

• Manufacturer Part Number: EP3SL150F1152C3N
• Description: IC STRATX III FPGA 150K 1152FBGA
• Manufacturer: Altera
• Series: Stratix® IIIr

Specifications of EP3SL150F1152C3N

• Number Of Logic Elements/cells: 142500
• Number Of Labs/clbs: 5700
• Total Ram Bits: 6390
• Number Of I /o: 744
• Voltage - Supply: 0.86 V ~ 1.15 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1152-FBGA
• For Use With: 544-2568 - KIT DEVELOPMENT STRATIX III
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Other names: 544-2408; EP3SL150F1152C3NES

Chapter 1: Stratix III Device Datasheet: DC and Switching Characteristics
Switching Characteristics
Table 1–25. True and Emulated LVDS Specifications for Stratix III Devices
Table 1–26. DPA Lock Time Specifications for Stratix III Devices
© July 2010 Altera Corporation
Non DPA Mode
Sampling Window
Notes to
(1) When J = 3 to 10, the SERDES block is used.
(2) When J = 1 or 2, the SERDES block is bypassed.
(3) Clock Boost Factor (W) is the ratio between the input data rate to the input clock rate.
(4) The minimum and maximum specification depends on the clock source (for example, the PLL and clock pin) and the clock routing resource (global, regional, or
(5) The t
(6) You can estimate the achievable maximum data rate for non-DPA mode by performing link timing closure analysis. Consider the board skew margin, transmitter
(7) This is achieved by using the LVDS and DPA clock network.
(8) If the receiver (with DPA enabled) and the transmitter are using shared PLLs, the minimum data rate is 150 Mbps.
(9) This is only applied to DPA and Soft-CDR modes.
SPI-4
Parallel Rapid
I/O
Standard
local) used. The I/O differential buffer and input register do not have a minimum toggle rate.
delay margin, as well as the receiver sampling margin to determine the maximum data rate supported.
Symbol
Table
xJitter
specification is for the true LVDS I/O standard only.
1–25:
0000000000
1111111111
00001111
10010000
Training
Pattern
Conditions
Table 1–26
—
Transitions
of Training
Repetition
Number of
Pattern
in one
Data
lists the DPA lock time specifications for Stratix III devices.
2
2
4
—
—
repetitions
Number of
Transition
C2
per 256
Data
128
128
(4)
64
300
PLL calibration
PLL calibration
PLL calibration
with DPA PLL
with DPA PLL
with DPA PLL
Condition
without DPA
without DPA
without DPA
calibration
calibration
calibration
—
(Note
C3, I3
—
1), (2),
(5)
(Note
300
3×256 data transitions +
3×256 data transitions +
3×256 data transitions +
(3)
2×96 slow clock cycles
2×96 slow clock cycles
2×96 slow clock cycles
1),
256 data transitions
256 data transitions
256 data transitions
(Part 1 of 2)
(2)
—
(Part 3 of 3)
Min
(6)
(6)
(6)
Stratix III Device Handbook, Volume 2
C4, I4
—
300
Typ
—
—
—
—
—
—
—
C4L, I4L
—
Max
1–23
—
—
—
—
—
—
300
ps