EP1C6Q240C6N Altera, EP1C6Q240C6N Datasheet - Page 64
![IC CYCLONE FPGA 5980 LE 240-PQFP](/photos/6/72/67260/544-240-pqfp_sml.jpg)
EP1C6Q240C6N
Manufacturer Part Number
EP1C6Q240C6N
Description
IC CYCLONE FPGA 5980 LE 240-PQFP
Manufacturer
Altera
Series
Cyclone®r
Datasheet
1.EP1C3T144C8.pdf
(106 pages)
Specifications of EP1C6Q240C6N
Number Of Logic Elements/cells
5980
Number Of Labs/clbs
598
Total Ram Bits
92160
Number Of I /o
185
Voltage - Supply
1.425 V ~ 1.575 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
240-MQFP, 240-PQFP
Family Name
Cyclone®
Number Of Logic Blocks/elements
5980
# I/os (max)
185
Frequency (max)
405.2MHz
Process Technology
0.13um (CMOS)
Operating Supply Voltage (typ)
1.5V
Logic Cells
5980
Ram Bits
92160
Operating Supply Voltage (min)
1.425V
Operating Supply Voltage (max)
1.575V
Operating Temp Range
0C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
240
Package Type
PQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Gates
-
Lead Free Status / Rohs Status
Compliant
Other names
544-1811
EP1C6Q240C6N
EP1C6Q240C6N
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP1C6Q240C6N
Manufacturer:
ALTERA
Quantity:
203
Part Number:
EP1C6Q240C6N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Cyclone Device Handbook, Volume 1
3–2
Preliminary
Note to
(1)
USERCODE
IDCODE
HIGHZ
CLAMP
ICR instructions
PULSE_NCONFIG
CONFIG_IO
SignalTap II
instructions
Table 3–1. Cyclone JTAG Instructions (Part 2 of 2)
JTAG Instruction
Bus hold and weak pull-up resistor features override the high-impedance state of HIGHZ, CLAMP, and EXTEST.
(1)
(1)
Table
3–1:
00 0000 0111
00 0000 0110
00 0000 1011
00 0000 1010
00 0000 0001
00 0000 1101
Instruction Code
In the Quartus II software, there is an Auto Usercode feature where you
can choose to use the checksum value of a programming file as the JTAG
user code. If selected, the checksum is automatically loaded to the
USERCODE register. Choose Assignments > Device > Device and Pin
Options > General. Turn on Auto Usercode.
—
—
Selects the 32-bit USERCODE register and places it between the
TDI and TDO pins, allowing the USERCODE to be serially shifted
out of TDO.
Selects the IDCODE register and places it between TDI and TDO,
allowing the IDCODE to be serially shifted out of TDO.
Places the 1-bit bypass register between the TDI and TDO pins,
which allows the BST data to pass synchronously through selected
devices to adjacent devices during normal device operation, while
tri-stating all of the I/O pins.
Places the 1-bit bypass register between the TDI and TDO pins,
which allows the BST data to pass synchronously through selected
devices to adjacent devices during normal device operation while
holding I/O pins to a state defined by the data in the boundary-scan
register.
Used when configuring a Cyclone device via the JTAG port with a
MasterBlaster
using a Jam File or Jam Byte-Code File via an embedded
processor.
Emulates pulsing the
even though the physical pin is unaffected.
Allows configuration of I/O standards through the JTAG chain for
JTAG testing. Can be executed before, after, or during
configuration. Stops configuration if executed during configuration.
Once issued, the
to reset the configuration device.
device is reconfigured.
Monitors internal device operation with the SignalTap II embedded
logic analyzer.
TM
or ByteBlasterMV
CONFIG_IO
nCONFIG
Description
instruction will hold
pin low to trigger reconfiguration
nSTATUS
TM
download cable, or when
is held low until the
Altera Corporation
nSTATUS
May 2008
low