XC4020E-4HQ208I Xilinx Inc, XC4020E-4HQ208I Datasheet - Page 62

no-image

XC4020E-4HQ208I

Manufacturer Part Number
XC4020E-4HQ208I
Description
IC FPGA I-TEMP 5V 4SPD 208-HQFP
Manufacturer
Xilinx Inc
Series
XC4000E/Xr
Datasheet

Specifications of XC4020E-4HQ208I

Number Of Logic Elements/cells
1862
Number Of Labs/clbs
784
Total Ram Bits
25088
Number Of I /o
160
Number Of Gates
20000
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
208-BFQFP Exposed Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
XC4020E-4HQ208I
Manufacturer:
XILINX
0
Part Number:
XC4020E-4HQ208I
Manufacturer:
XLINX
Quantity:
5 530
Part Number:
XC4020E-4HQ208I
Manufacturer:
Xilinx Inc
Quantity:
10 000
Part Number:
XC4020E-4HQ208I
Manufacturer:
XILINX
0
XC4000E and XC4000X Series Field Programmable Gate Arrays
Asynchronous Peripheral Mode
Write to FPGA
Asynchronous Peripheral mode uses the trailing edge of
the logic AND condition of WS and CS0 being Low and RS
and CS1 being High to accept byte-wide data from a micro-
processor bus. In the lead FPGA, this data is loaded into a
double-buffered UART-like parallel-to-serial converter and
is serially shifted into the internal logic.
The lead FPGA presents the preamble data (and all data
that overflows the lead device) on its DOUT pin. The
RDY/BUSY output from the lead FPGA acts as a hand-
shake signal to the microprocessor. RDY/BUSY goes Low
when a byte has been received, and goes High again when
the byte-wide input buffer has transferred its information
into the shift register, and the buffer is ready to receive new
data. A new write may be started immediately, as soon as
the RDY/BUSY output has gone Low, acknowledging
receipt of the previous data. Write may not be terminated
until RDY/BUSY is High again for one CCLK period. Note
that RDY/BUSY is pulled High with a high-impedance
pull-up prior to INIT going High.
The length of the BUSY signal depends on the activity in
the UART. If the shift register was empty when the new byte
was received, the BUSY signal lasts for only two CCLK
periods. If the shift register was still full when the new byte
was received, the BUSY signal can be as long as nine
CCLK periods.
Note that after the last byte has been entered, only seven of
its bits are shifted out. CCLK remains High with DOUT
equal to bit 6 (the next-to-last bit) of the last byte entered.
6-66
Figure 58:
Asynchronous Peripheral Mode Circuit Diagram
CONTROL
SIGNALS
4.7 k
REPROGRAM
Product Obsolete or Under Obsolescence
V
CC
4.7 k
4.7 k
ADDRESS
DATA
BUS
BUS
ADDRESS
DECODE
LOGIC
8
CS0
DONE
D0–7
CS1
RS
WS
RDY/BUSY
INIT
PROGRAM
N/C
M0
PERIPHERAL
ASYNCHRO-
XC4000E/X
4.7 k
NOUS
M1
The READY/BUSY handshake can be ignored if the delay
from any one Write to the end of the next Write is guaran-
teed to be longer than 10 CCLK periods.
Status Read
The logic AND condition of the CS0, CS1and RS inputs
puts the device status on the Data bus.
• D7 High indicates Ready
• D7 Low indicates Busy
• D0 through D6 go unconditionally High
It is mandatory that the whole start-up sequence be started
and completed by one byte-wide input. Otherwise, the pins
used as Write Strobe or Chip Enable might become active
outputs and interfere with the final byte transfer. If this
transfer does not occur, the start-up sequence is not com-
pleted all the way to the finish (point F in
53).
In this case, at worst, the internal reset is not released. At
best, Readback and Boundary Scan are inhibited. The
length-count value, as generated by the XACT step soft-
ware, ensures that these problems never occur.
Although RDY/BUSY is brought out as a separate signal,
microprocessors can more easily read this information on
one of the data lines. For this purpose, D7 represents the
RDY/BUSY status when RS is Low, WS is High, and the
two chip select lines are both active.
Asynchronous Peripheral mode is selected by a <101> on
the mode pins (M2, M1, M0).
DOUT
M2
CCLK
N/C
OPTIONAL
DAISY-CHAINED
FPGAs
DIN
DONE
CCLK
INIT
PROGRAM
M0
XC4000E/X
SLAVE
N/C
M1
May 14, 1999 (Version 1.6)
X9028
DOUT
M2
Figure 47 on page
R

Related parts for XC4020E-4HQ208I