20-101-1028 Rabbit Semiconductor, 20-101-1028 Datasheet - Page 34
20-101-1028
Manufacturer Part Number
20-101-1028
Description
MODULE RABBITCORE RCM3750
Manufacturer
Rabbit Semiconductor
Datasheet
1.20-101-1028.pdf
(172 pages)
Specifications of 20-101-1028
Module/board Type
MPU Core Module
Product
Microcontroller Modules
Core Processor
Rabbit 3000
Flash
512 KBytes
Operating Supply Voltage
4.75 to 5.25 V
Board Size
75 mm x 30 mm x 23 mm
For Use With/related Products
RCM3750
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
316-1110
- Current page: 34 of 172
- Download datasheet (3Mb)
4.2.2 Ethernet Port
Figure 8 shows the pinout for the RJ-45 Ethernet port (J3). Note that some Ethernet con-
nectors are numbered in reverse to the order used here.
Two LEDs are placed next to the RJ-45 Ethernet jack, one to indicate an Ethernet link
(
of the RJ-45 Ethernet jack indicates that the RCM3750 is connected to a functioning
100Base-T network.
The RJ-45 connector is shielded to minimize EMI effects to/from the Ethernet signals.
4.2.3 Serial Programming Port
The RCM3750 programming port is accessed through header J2 or over an Ethernet con-
nection via the RabbitLink EG2110. The programming port uses the Rabbit 3000’s Serial
Port A for communication. Dynamic C uses the programming port to download and debug
programs.
The programming port is also used for the following operations.
• Cold-boot the Rabbit 3000 on the RCM3750 after a reset.
• Remotely download and debug a program over an Ethernet connection using the
• Fast copy designated portions of flash memory from one Rabbit-based board (the
Serial Port A has special features that allow it to cold-boot the system after reset. Serial
Port A is also the port that is used for software development under Dynamic C.
Alternate Uses of the Programming Port
All three clocked Serial Port A signals are available as
• a synchronous serial port
• an asynchronous serial port, with the clock line usable as a general CMOS input
28
LINK
RabbitLink EG2110.
master) to another (the slave) using the Rabbit Cloning Board.
) and one to indicate Ethernet activity (
Figure 8. RJ-45 Ethernet Port Pinout
ETHERNET
ACT
). A third LED (
SPD
RabbitCore RCM3750
) on the other side
Related parts for 20-101-1028
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: