20-101-0709 Rabbit Semiconductor, 20-101-0709 Datasheet - Page 31
20-101-0709
Manufacturer Part Number
20-101-0709
Description
INTERFACE GRAPHIC DISPLAY OP6700
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0412.pdf
(90 pages)
Specifications of 20-101-0709
Module/board Type
Single Board Computer Module
For Use With/related Products
OP6700
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
20-101-709
20-101-709
20-101-709
- Current page: 31 of 90
- Download datasheet (2Mb)
3.3 Programming Cable
The programming cable is used to connect the Intellicom tprogramming port o a PC serial
COM port. The programming cable converts the RS-232 voltage levels used by the PC
serial port to the voltage levels used by the Rabbit 2000.
When the
connector on the programming cable is connected to the Intellicom
PROG
programming port, programs can be downloaded and debugged over the serial interface
between the PC and the Rabbit 2000.
The
connector of the programming cable may be used on header J4 of the Intellicom
DIAG
with the Intellicom operating in the Run Mode. This allows the programming port to be
used as a regular serial port.
3.3.1 Changing Between Program Mode and Run Mode
The Intellicom is automatically in Program Mode when the
connector on the pro-
PROG
gramming cable is attached, and is automatically in Run Mode when no programming
cable is attached. When the Rabbit 2000 is reset, the operating mode is determined by the
status of the SMODE pins. When the programming cable’s
connector is attached,
PROG
the SMODE pins are pulled high, placing the Rabbit 2000 in the Program Mode. When the
programming cable’s
PROG
connector is not attached, the SMODE pins are pulled low,
causing the Rabbit 2000 to operate in the Run Mode.
Figure 11. Intellicom Program Mode and Run Mode Set-Up
A program “runs” in either mode, but can only be downloaded and debugged when the
OP6800 is in the Program Mode.
Refer to the
for more information on the pro-
Rabbit 2000 Microprocessor User’s Manual
gramming port and the programming cable.
User’s Manual
27
Related parts for 20-101-0709
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: