Document Number: 42016
Revision 13-Nov-03
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 85°C.
Insulation Resistance: After a 2 minute charge at rated
Capacitance, Tolerance and Dissipation Factor:
DIMENSIONS in inches [millimeters]
To + 105°C when working voltage is reduced to 70% of
+ 85°C rating; to + 125°C when working voltage is reduced
to 50% of + 85°C rating.
voltage or 500 V, whichever is less.
At + 25°C: 100,000 Megohm for C ≤ .25 Microfarads.
25,000 Megohm - Microfarads for C > .25 Microfarads.
At + 85°C: 10,000 Megohm for C ≤ .15 Microfarads.
1500 Megohm - Microfarads for C > .15 Microfarads.
At + 105°C: 1500 Megohm for C ≤ .17 Microfarads.
250 Megohm - Microfarads for C > .17 Microfarads.
At + 125°C: 200 Megohm for C ≤ .13 Microfarads.
25 Megohm - Microfarads for C > .13 Microfarads.
Capacitors shall be measured at a frequency of 1000Hz
@ + 25°C or else be referred to measurements made at
that frequency and temperature. The maximum dissipation
factor shall be .75%.
Length
Lead
±
0.060 [1.524]
Terminal A
CODE
CASE
Max.
W
X
Y
L
S
Filmite "E", ORANGE DROP
[31.750]
1.250
Max.
For technical questions, contact spresale@vishay.com
Length
Lead
0.70 [17.78]
0.80 [20.32]
1.25 [31.75]
Polyester Capacitors
Terminal B
(Max.)
±
L
0.030 [0.762]
Max.
S
L
[6.020]
0.237
Max.
FEATURES
• Utilizes minimum area where printed wiring board space
• Wound from PETP polyester film and thin gauge foil
• Protected against moisture by a conformal coating of
• Specifically designed for printed wiring board applications
• Widely used in computers, instrumentation and
• 100 VDC through 600 VDC, may be operated up to
Dielectric Withstanding Voltage: Capacitors shall
Humidity Test: Condition capacitors with no voltage
DC Life Test: Capacitors are capable of withstanding a
withstand a DC potential of 250% of rated voltage applied
between terminals for not more than 5 seconds. The test
voltage must be applied and discharged through a resistor
of 1 ohm per volt.
applied for 72 hours @ 95% relative humidity and + 75°C.
Remove capacitors from humidity chamber, wipe surface
dry of moisture and dry in circulating air for 4 hours.
Measure insulation resistance after a 2 minute charge
@ + 25°C and rated voltage or 500 VDC, whichever is less.
Minimum product of insulation resistance and capacitance
shall be 5000 Megohm - Microfarads after test but need not
exceed 10,000 Megohm. Not more than one failure
allowed in 12 units tested.
500 hour life test @ + 85°C @ 150% of rated working
voltage. After test, capacitance shall not have changed by
more than 5% of initial value, insulation resistance shall not
have decreased by more than 50% of the initial limit and
dissipation factor shall not have increased to more than 1%.
is most important
under carefully controlled atmospheric conditions
epoxy
telecommunications equipment
+ 125°C with proper derating
Terminal A and B
.562 [14.275]
.613 [15.570]
.969 [24.613]
®
, Radial Lead
Length
Max.
Lead
H
±
Terminal D
0.030 [0.762]
Max.
L
S
S
[6.020]
0.237
Max.
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
Vishay Sprague
.719 [18.263]
Terminal D
.375 [9.525]
.375 [9.525]
Type 225P
www.vishay.com
T Max.
39