CY7C68000A-56LTXC Cypress Semiconductor Corp, CY7C68000A-56LTXC Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CY7C68000A-56LTXC
Manufacturer Part Number
CY7C68000A-56LTXC
Description
IC TXRX USB 2.0 TX2 56VQFN
Manufacturer
Cypress Semiconductor Corp
Series
CY7Cr
Type
Transceiverr
Datasheet
1.CY7C68000A-56BAXC.pdf
(15 pages)
Specifications of CY7C68000A-56LTXC
Protocol
USB 2.0
Voltage - Supply
3 V ~ 3.6 V
Mounting Type
Surface Mount
Package / Case
56-VQFN Exposed Pad, 56-HVQFN, 56-SQFN, 56-DHVQFN
For Use With
CY3685 - KIT DEV EZ-USB NX2LPCY3683 - KIT EZ-USB TX2 DEVELOPMENT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Table 1. Pin Descriptions (continued)
Document #: 38-08052 Rev. *H
QFN VFBGA
21
22
23
56
51
52
55
17
28
32
45
53
16
20
30
42
47
40
35
25
6
5
A4
B7
A6
A7
A2
H3
H2
A3
C6
C7
D7
E7
E8
C4
C5
C3
D1
D2
G6
C8
F7
F2
RXValid
RXActive
RXError
ValidH
DataBus16_8
XTALIN
XTALOUT
Uni_Bidi
V
V
V
V
V
GND
GND
GND
GND
GND
Reserved
Reserved
Reserved
Reserved
CC
CC
CC
CC
CC
Name
Ground
Ground
Ground
Ground
Ground
Output
Output
Output
Output
INPUT
INPUT
INPUT
INPUT
Power
Power
Power
Power
Power
Type
Input
Input
Input
I/O
Default
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Receive Data Valid This signal indicates that the DataOut bus has valid
data. The Receive Data Holding Register is full and ready to be unloaded.
The SIE is expected to latch the DataOut bus on the clock edge.
Receive Active This signal indicates that the receive state machine has
detected SYNC and is active.
RXActive is negated after a bit stuff error or an EOP is detected.
Receive Error
0 Indicates no error.
1 Indicates that a receive error has been detected.
ValidH This signal indicates that the high-order eight bits of a 16-bit data
word presented on the Data bus are valid. When DataBus16_8 = 1 and
TXValid = 0, ValidH is an output, indicating that the high-order receive
data byte on the Data bus is valid. When DataBus16_8 = 1 and TXValid
= 1, ValidH is an input and indicates that the high-order transmit data byte,
presented on the Data bus by the transceiver, is valid. When
DataBus16_8 = 0, ValidH is undefined. The status of the receive
low-order data byte is determined by RXValid and are present on D0–D7.
Data Bus 16_8 This signal selects between 8- and 16-bit data transfers.
1–16-bit data path operation enabled. CLK = 30 MHz.
0–8-bit data path operation enabled. When Uni_Bidi = 0, D[8:15] are un-
defined. When Uni_Bidi =1, D[0:7] are valid on TxValid and D[8:15] are
valid on RxValid. CLK = 60 MHz
Note: DataBus16_8 is static after Power-on Reset (POR) and is only
sampled at the end of Reset.
Crystal Input Connect this signal to a 24 MHz parallel-resonant, funda-
mental mode crystal and 30 pF capacitor to GND.
It is also correct to drive XTALIN with an external 24 MHz square wave
derived from another clock source.
Crystal Output Connect this signal to a 24 MHz parallel-resonant, funda-
mental mode crystal and 30 pF (nominal) capacitor to GND. If an external
clock is used to drive XTALIN, leave this pin open.
Driving this pin HIGH enables the unidirectional mode when the 8-bit
interface is selected. Uni_Bidi is static after power-on reset (POR).
V
Ground.
Ground.
Ground.
Ground.
Ground.
Connect pin to Ground.
Connect pin to Ground.
Connect pin to Ground.
Connect pin to Ground.
V
V
V
V
CC
CC
CC
CC
CC
. Connect to 3.3V power source.
. Connect to 3.3V power source.
. Connect to 3.3V power source.
. Connect to 3.3V power source.
. Connect to 3.3V power source.
Description
[1]
(continued)
CY7C68000A
Page 8 of 15
[+] Feedback