QT113-IS Atmel, QT113-IS Datasheet
QT113-IS
Specifications of QT113-IS
Related parts for QT113-IS
QT113-IS Summary of contents
Page 1
... Appliance control ! Access systems ! Security systems ! Pointing devices S AVAILABLE OPTIONS T SOIC +70 C QT113 +70 C QT113H +85 C QT113- +85 C QT113H-IS QProx™ ™ ™ ™ QT113 / QT113H -T T RANSFER OUCH pt1 3 O pt2 4 ! Elevator buttons ! Toys & games and electrode external switches, opamps, or other ...
Page 2
... The QT switches and charge measurement hardware functions are all internal to the QT113 (Figure 1-2). A 14-bit single-slope switched capacitor ADC includes both the required QT charge and transfer switches in a configuration that provides direct ADC conversion. The ADC is designed to ...
Page 3
... S ENSITIVITY The QT113 can be set for one of 2 gain levels using option pin 5 (Table 1-1). This sensitivity change is made by altering the internal numerical threshold level required for a detection. Note that sensitivity is also a function of other things: like the ...
Page 4
... Decreasing Sensitivity In some cases the QT113 may be too sensitive, even on low gain. In this case gain can be lowered further by a number of strategies: making the electrode smaller, making the ...
Page 5
... OPT1 and OPT2. All options are shown in Table 2-1. 2.2 The output of the QT113 can respond mode, where the output is active-low upon detection. The output will remain active-low for the duration of the detection, or until the Max On-Duration expires (if not infinite), whichever occurs first ...
Page 6
... O D UTPUT RIVE The QT113’s `output is active low and can sink up to 5mA of non-inductive current inductive load is used, such as a small relay, the load should be diode clamped to prevent damage. When set to operate in a proximity mode (at high gain) the current should be limited to 1mA to prevent gain ...
Page 7
... The currents should not be allowed to traverse the area directly under the QT113. If the QT113 is connected to an external circuit via a cable or long twisted pair possible for ground-bounce to cause damage to the Out pin; even though the transients are led ...
Page 8
ABSOLUTE MAXIMUM SPECIFICATIONS Operating temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 9
DC SPECIFICATIONS Vdd = 3.0V 10nF 5pF, T Parameter Description V Supply voltage DD I Supply current DD V Supply turn-on slope DDS V Low input logic level IL V High input logic level HL ...
Page 10
... ORDERING INFORMATION PART QT113-D QT113-S QT113-IS QT113H-D QT113H-S QT113H-IS Chart 4-3 - Typical Response Time vs. Cx; Vdd = 3.0 100.00 10.00 1. Load TEMP RANGE PACKAGE 0 - 70C 0 - 70C -40 - 85C 0 - 70C 0 - 70C -40 - 85C - 10 - 10nF 20nF 50nF 100nF 200nF 500nF 30 40 MARKING PDIP QT1 + 13 SOIC-8 ...
Page 11
Package type: 8-pin Dual-In-Line Millimeters SYMBOL Min a 6.096 A 7.62 M 9.017 m 7.62 Q 0.889 P 0.254 L 0.355 L1 1.397 F 2.489 R 3.048 r 0.381 S 3.048 7.62 x 8.128 Y 0.203 Millimeters ...
Page 12
Quantum Research Group Ltd Enterprise House, Southampton, Hants SO14 3XB Tel: +44 (0)23 8045 3934 Fax: +44 (0)23 8045 3939 This device expressly not for use in any medical or human safety related application without the express written consent of ...