EVAL-ADM1062-69CSZ Analog Devices Inc, EVAL-ADM1062-69CSZ Datasheet
EVAL-ADM1062-69CSZ
Specifications of EVAL-ADM1062-69CSZ
Related parts for EVAL-ADM1062-69CSZ
EVAL-ADM1062-69CSZ Summary of contents
Page 1
FEATURES Complete supervisory and sequencing solution for supplies 10 supply fault detectors enable supervision of supplies to <0.5% accuracy at all voltages at 25°C <1.0% accuracy across all voltages and temperatures 5 selectable input attenuators allow supervision ...
Page 2
ADM1062 TABLE OF CONTENTS Features .............................................................................................. 1 Functional Block Diagram .............................................................. 1 Applications....................................................................................... 1 General Description ......................................................................... 1 Revision History ............................................................................... 2 Detailed Block Diagram .................................................................. 3 Specifications..................................................................................... 4 Absolute Maximum Ratings............................................................ 7 Thermal Resistance ...................................................................... 7 ESD Caution.................................................................................. 7 ...
Page 3
Supply margining can be performed with a minimum of external components. The margining loop can be used for in-circuit testing of a board during production (for example, to verify board functionality at −5% of nominal supplies can be ...
Page 4
ADM1062 SPECIFICATIONS 3 14 VPx = 3 6.0 V Table 1. Parameter POWER SUPPLY ARBITRATION VH, VPx VPx VH VDDCAP C VDDCAP POWER SUPPLY Supply Current VPx ...
Page 5
Parameter Conversion Time Offset Error Input Noise 2 TEMPERATURE SENSOR Local Sensor Accuracy Local Sensor Supply Voltage Coefficient Remote Sensor Accuracy Remote Sensor Supply Voltage Coefficient Remote Sensor Current Source Temperature for Code 0x800 Temperature for Code 0xC00 Temperature Resolution ...
Page 6
ADM1062 Parameter SINK R PULL- (VPx) SOURCE Three-State Output Leakage Current Oscillator Frequency DIGITAL INPUTS (VXx, A0, A1) Input High Voltage Input Low Voltage Input High Current ...
Page 7
ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Voltage on VH Pin Voltage on VPx Pins Voltage on VXx Pins Voltage on A0, A1 Pins Voltage on REFIN, REFOUT Pins Voltage on VDDCAP, VCCP Pins Voltage on PDOx Pins Voltage on SDA, ...
Page 8
ADM1062 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS VX1 1 PIN 1 VX2 INDICATOR 2 VX3 3 VX4 4 ADM1062 VX5 5 TOP VIEW VP1 6 (Not to Scale) VP2 7 VP3 8 VP4 ...
Page 9
Pin No. 1 Mnemonic LFCSP TQFP 39 46 VDDCAP GND 1 Note that the LFCSP has an exposed pad on the bottom. This pad connect (NC). If possible, this pad should be soldered to ...
Page 10
ADM1062 TYPICAL PERFORMANCE CHARACTERISTICS (V) VP1 Figure 5. V vs. V VDDCAP (V) VH Figure ...
Page 11
I (µA) LOAD Figure 11. Charge-Pumped V (FET Drive Mode) vs. I PDO1 5.0 4.5 4.0 3.5 3.0 2.5 VP1 = 3V 2.0 1.5 1.0 0.5 0 ...
Page 12
ADM1062 1 CH1 200mV M1.00µs CH1 756mV Figure 17. Transient Response of DAC Code Change into Typical Load 1 CH1 200mV M1.00µs CH1 Figure 18. Transient Response of DAC to Turn-On from High-Z State DAC 20kΩ BUFFER PROBE OUTPUT POINT ...
Page 13
POWERING THE ADM1062 The ADM1062 is powered from the highest voltage input on either the positive-only supply inputs (VPx) or the high voltage supply input (VH). This technique offers improved redundancy because the device is not dependent on any particular ...
Page 14
ADM1062 INPUTS SUPPLY SUPERVISION The ADM1062 has 10 programmable inputs. Five of these are dedicated supply fault detectors (SFDs). These dedicated inputs are called VH and VPx (VP1 to VP4) by default. The other five inputs are labeled VXx (VX1 ...
Page 15
The hysteresis value is given × N /255 HYST R THRESH where the desired hysteresis voltage. HYST N is the decimal value of the 5-bit hysteresis code. THRESH Note that N has a maximum ...
Page 16
ADM1062 OUTPUTS SUPPLY SEQUENCING THROUGH CONFIGURABLE OUTPUT DRIVERS Supply sequencing is achieved with the ADM1062 using the programmable driver outputs (PDOs) on the device as control signals for supplies. The output drivers can be used as logic enables or as ...
Page 17
SEQUENCING ENGINE OVERVIEW The ADM1062 sequencing engine (SE) provides the user with powerful and flexible control of sequencing. The SE implements a state machine control of the PDO outputs, with state changes conditional on input events. SE programs can enable ...
Page 18
ADM1062 SEQUENCING ENGINE APPLICATION EXAMPLE The application in this section demonstrates operation of the SE. Figure 28 shows how the simple building block of a single SE state can be used to build a power-up sequence for a three- supply ...
Page 19
Monitoring Fault Detector The monitoring fault detector block is used to detect a failure on an input. The logical function implementing this is a wide OR gate that can detect when an input deviates from its expected condition. The clearest ...
Page 20
ADM1062 VOLTAGE READBACK The ADM1062 has an on-board, 12-bit, accurate ADC for voltage readback over the SMBus. The ADC has a 12-channel analog mux on the front end. The 12 channels consist of the 10 SFD inputs (VH, VPx, and ...
Page 21
SUPPLY MARGINING OVERVIEW It is often necessary for the system designer to adjust supplies, either to optimize their level or force them away from nominal values to characterize the system performance under these condi- tions. This is a function typically ...
Page 22
ADM1062 VIN DC-TO-DC CONVERTER OUTPUT FEEDBACK WRITING TO THE DACS Four DAC ranges are offered. They can be placed with midcode (Code 0x7F) at 0.6 V, 0.8 V, 1.0 V, and 1.25 V. These voltages are placed to correspond to ...
Page 23
TEMPERATURE MEASUREMENT SYSTEM The ADM1062 contains an on-chip, band gap temperature sensor whose output is digitized by the on-chip, 12-bit ADC. Theoretically, the temperature sensor and the ADC can measure temperatures from −128°C to +128°C with a resolution of 0.125°C. ...
Page 24
ADM1062 To measure ΔV , the sensor is switched between operating BE currents of I and N × I. The resulting waveform is passed through a 65 kHz low-pass filter to remove noise and through a chopper- stabilized amplifier that ...
Page 25
APPLICATIONS DIAGRAM 12V OUT 3V OUT 3.3V OUT 2.5V OUT 1.8V OUT 1.2V OUT 0.9V OUT POWRON RESET *ONLY ONE MARGINING CIRCUIT SHOWN FOR CLARITY. DAC1 TO DAC6 ALLOW MARGINING FOR UP TO SIX ...
Page 26
ADM1062 COMMUNICATING WITH THE ADM1062 CONFIGURATION DOWNLOAD AT POWER-UP The configuration of the ADM1062 (undervoltage/overvoltage thresholds, glitch filter timeouts, PDO configurations, and so on) is dictated by the contents of the RAM. The RAM comprises digital latches that are local ...
Page 27
POWER-UP (V > 2.5V) CC EEPROM UPDATING THE SEQUENCING ENGINE Sequencing engine (SE) functions are not updated in the same way as regular configuration latches. The SE has its own dedicated 512-byte nonvolatile, electrically erasable, programmable, read- only memory (EEPROM) ...
Page 28
ADM1062 The device also has several identification registers (read-only) that can be read across the SMBus. Table 13 lists these registers with their values and functions. Table 13. Identification Register Values and Functions Name Address Value Function MANID 0xF4 0x41 ...
Page 29
SCL SDA START BY MASTER FRAME 1 SLAVE ADDRESS 1 SCL (CONTINUED) SDA (CONTINUED) FRAME 3 DATA BYTE Figure 40. General SMBus Read Timing Diagram t ...
Page 30
ADM1062 SMBus PROTOCOLS FOR RAM AND EEPROM The ADM1062 contains volatile registers (RAM) and non- volatile registers (EEPROM). User RAM occupies Address 0x00 to Address 0xDF; the EEPROM occupies Address 0xF800 to Address 0xFBFF. Data can be written to and ...
Page 31
To set up a 2-byte EEPROM address for a subsequent read, write, block read, block write, or page erase. In this case, the command byte is the high byte of EEPROM Address 0xF8 to EEPROM Address 0xFB. The only ...
Page 32
ADM1062 Block Read In a block read operation, the master device reads a block of data from a slave device. The start address for a block read must have been set previously. In the ADM1062, this is done by a ...
Page 33
OUTLINE DIMENSIONS PIN 1 INDICATOR 12° MAX 1.00 0.85 0.80 SEATING PLANE 1.05 1.00 0.95 0.15 0.05 ROTATED 90° CCW 6.00 BSC SQ 0.60 MAX 0.50 TOP BSC 5.75 VIEW BCS SQ 0.50 0.40 0.30 0.80 MAX 0.65 TYP 0.05 ...
Page 34
... Z = RoHS Compliant Part. Package Description 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 40-Lead LFCSP_VQ 48-Lead TQFP 48-Lead TQFP 48-Lead TQFP 48-Lead TQFP Evaluation Kit (LFCSP Version) Evaluation Kit (TQFP Version) Rev Page Package Option CP-40-1 CP-40-1 CP-40-1 CP-40-1 SU-48 SU-48 SU-48 SU-48 ...
Page 35
NOTES Rev Page ADM1062 ...
Page 36
ADM1062 NOTES ©2005–2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04433-0-5/08(B) Rev Page ...