S3005 AMCC (Applied Micro Circuits Corp), S3005 Datasheet

no-image

S3005

Manufacturer Part Number
S3005
Description
SONET/SDH OC-3/12 Transmitter and Receiver(?????????SONET/SDH???)
Manufacturer
AMCC (Applied Micro Circuits Corp)
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S30050-Q5880-X200-2
Manufacturer:
QS
Quantity:
6 218
Part Number:
S300511
Manufacturer:
NELLCOR
Quantity:
11
Part Number:
S3005C-1
Manufacturer:
a
Quantity:
8
EVALUATION BOARD DESCRIPTION
The S6004 SONET Evaluation Board allows dem-
onstration of AMCC's S3005 and S3006 SONET/
SDH OC-3/12 transmitter/receiver chipset. This data
sheet provides information on board contents and
layout. It should be used in conjunction with the
S3005/S3006 data sheets, which contain full techni-
cal details on chip operation.
Figure 1 depicts the layout of the evaluation board,
showing the location of connectors and components.
Power is supplied to the board from external sup-
plies connected through the on-board banana jacks.
Connectors allow easy access to all of the interface
signals on the S3005/S3006 chips.
Figure 1. Board Layout
Applied Micro Circuits Corporation
6195 Lusk Blvd., San Diego, CA 92121 • (619) 450-9333
EVALUATION BOARD
S3005/S3006 EVALUATION BOARD
BiCMOS PECL CLOCK GENERATOR
S3005/S3006 EVALUATION BOARD
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
1
3
5
7
9
RESET
H1
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
2
4
6
8
H2
S1
S3005
TSCLKN
TSCLKP
REFCLKN
REFCLKP
S2
JP2
1
0
LLCLKN
LLCLKP
TSDN
TSDP
DLDP
DLDN
LLDP
LLDN
JPA
JPB
U2
–2V
LLCLKP
LLCLKN
RSDP
RSDN
LLDP
LLDN
DLDP
DLDN
D1
August 4, 1994
JP1
REFCLKP
REFCLKN
VEE
GND
U1
S3006
VCC
GND
S3006
XTAL
1
0
S3
LEDVCC
LEDGND
H4
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
1
3
5
7
9
H3
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
2
4
6
8
S6004
S6004
Page 1
®

Related parts for S3005

S3005 Summary of contents

Page 1

... SDH OC-3/12 transmitter/receiver chipset. This data sheet provides information on board contents and layout. It should be used in conjunction with the S3005/S3006 data sheets, which contain full techni- cal details on chip operation. Figure 1 depicts the layout of the evaluation board, showing the location of connectors and components. ...

Page 2

... Power connections are made through the on-board banana jacks (VCC, VEE, GND, LEDVCC, and LEDGND). Refer to Table 1 for recommended oper- ating conditions. A –2V connection provides proper on-board termination for the DLDP/N outputs of the S3005 when connected to the DLDP/N inputs of the S3006. Description Pin Names Ground ...

Page 3

... DIP Switch S2 position 4 TTL Input DLCV input (pin 59) of S3005 TTL Input DIP Switch S2 position 3 TTL Input DLEB input (pin 26) of S3005 and (pin 57) of S3006 TTL Input DIP Switch S2 position 2 TTL Input LLEB input (pin 57) of S3005 TTL Input DIP Switch S2 position 1 ...

Page 4

... S3005/S3006 EVALUATION BOARD RESET When the RSTB pins on Header H2 are shorted to each other, the push button switch on the top left of the board is connected to the S3005 and S3006 RSTB Master Reset inputs. CRYSTAL REFERENCES AND CLOCK GENERATION Two 19.44-MHz differential ECL crystal oscillators with 100-ppm stability are provided, one each for the transmitter and receiver ...

Page 5

... SMA connector, install jumpers on JP4 and JP6. (See Table 9, Jumpers.) LEDs The bank of 10 LEDs (D1) display when the S3005/ S3006 chips are locked, and also light when the ap- propriate POUT is in the high state. The function of each LED is shown in Table 8, and is also labeled on the board ...

Page 6

... JP10 are disconnected, as required when the S3005 REFCLKP/N SMA connectors are used for an external reference.) 4. Set TESTEN (H1 pin 26) on the S3005 High, to put the S3005 into bypass mode, which bypasses the PLL-generated clock source and enables the use of the REFCLKP/N as the bit rate clock input. ...

Related keywords