SAM4S16C Atmel Corporation, SAM4S16C Datasheet - Page 692

no-image

SAM4S16C

Manufacturer Part Number
SAM4S16C
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of SAM4S16C

Flash (kbytes)
1024 Kbytes
Pin Count
100
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
79
Ext Interrupts
79
Usb Transceiver
1
Quadrature Decoder Channels
2
Usb Speed
Full Speed
Usb Interface
Device
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Sd / Emmc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
16
Adc Resolution (bits)
12
Adc Speed (ksps)
1000
Analog Comparators
1
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
12
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
128
Self Program Memory
YES
External Bus Interface
1
Dram Memory
No
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
692
692
SAM4S
SAM4S
If STTTO is performed, the counter clock is stopped until a first character is received. The idle
state on RXD before the start of the frame does not provide a time-out. This prevents having to
obtain a periodic interrupt and enables a wait of the end of frame when the idle state on RXD is
detected.
If RETTO is performed, the counter starts counting down immediately from the value TO. This
enables generation of a periodic interrupt so that a user time-out can be handled, for example
when no key is pressed on a keyboard.
Figure 31-24
Figure 31-24. Receiver Time-out Block Diagram
Table 31-11
Table 31-11. Maximum Time-out Period
• Obtain an interrupt while no character is received. This is performed by writing US_CR with
RETTO
on RXD before a new character is received will not provide a time-out. This prevents having
to handle an interrupt before a character is received and allows waiting for the next idle state
on RXD after a frame is received.
the RETTO (Reload and Start Time-out) bit to 1. If RETTO is performed, the counter starts
counting down immediately from the value TO. This enables generation of a periodic interrupt
so that a user time-out can be handled, for example when no key is pressed on a keyboard.
Character
Received
Baud Rate
STTTO
gives the maximum time-out period for some standard baud rates.
bit/sec
14400
19200
28800
33400
1 200
2 400
4 800
9 600
shows the block diagram of the Receiver Time-out feature.
600
1
D
Clear
Q
Baud Rate
Clock
Clock
Bit Time
1 667
833
417
208
104
µs
69
52
35
30
16-bit Time-out
Counter
TO
Load
16-bit
Value
0
Time-out
109 225
54 613
27 306
13 653
6 827
4 551
3 413
2 276
1 962
11100A–ATARM–28-Oct-11
11100A–ATARM–28-Oct-11
ms
=
TIMEOUT

Related parts for SAM4S16C