TDA1519C NXP Semiconductors, TDA1519C Datasheet - Page 17

no-image

TDA1519C

Manufacturer Part Number
TDA1519C
Description
Manufacturer
NXP Semiconductors
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TDA1519C/N3
Manufacturer:
ST
0
Part Number:
TDA1519C/N3C
Manufacturer:
NXP
Quantity:
18 673
Part Number:
TDA1519CCU
Manufacturer:
Integrated
Quantity:
20
Part Number:
TDA1519CCU
Manufacturer:
NXP
Quantity:
10 995
Part Number:
TDA1519CL
Manufacturer:
UTC/友顺
Quantity:
20 000
Company:
Part Number:
TDA1519CL-H09
Quantity:
18 254
Part Number:
TDA1519CSP
Manufacturer:
JAE
Quantity:
1 500
Part Number:
TDA1519CSP
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
TDA1519CT
Manufacturer:
ERICSSON
Quantity:
52
Part Number:
TDA1519CTD
Manufacturer:
ST
0
Part Number:
TDA1519CTD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
TDA1519CTH
Manufacturer:
NXP
Quantity:
5 510
Part Number:
TDA1519CTH
Manufacturer:
MIC
Quantity:
5 510
Part Number:
TDA1519CTH
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
NXP Semiconductors
SOLDERING
Introduction
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mount components are mixed on
one printed-circuit board. Wave soldering can still be used
for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is
recommended. Driven by legislation and environmental
forces the worldwide use of lead-free solder pastes is
increasing.
Through-hole mount packages
S
Typical dwell time of the leads in the wave ranges from
3 to 4 seconds at 250 C or 265 C, depending on solder
material applied, SnPb or Pb-free respectively.
The total contact time of successive solder waves must not
exceed 5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (T
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
M
Apply the soldering iron (24 V or less) to the lead(s) of the
package, either below the seating plane or not more than
2 mm above it. If the temperature of the soldering iron bit
is less than 300 C it may remain in contact for up to
10 seconds. If the bit temperature is between
300 and 400 C, contact may be up to 5 seconds.
Surface mount packages
R
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
2004 Jan 28
OLDERING BY DIPPING OR BY SOLDER WAVE
EFLOW SOLDERING
ANUAL SOLDERING
22 W BTL or 2  11 W
stereo power amplifier
stg(max)
). If the
17
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 270 C depending on solder paste material. The
top-surface temperature of the packages should
preferably be kept:
 below 225 C (SnPb process) or below 245 C (Pb-free
 below 240 C (SnPb process) or below 260 C (Pb-free
Moisture sensitivity precautions, as indicated on packing,
must be respected at all times.
W
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
 Use a double-wave soldering method comprising a
 For packages with leads on two sides and a pitch (e):
 For packages with leads on four sides, the footprint must
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
AVE SOLDERING
process)
– for all the BGA, HTSSON..T and SSOP-T packages
– for packages with a thickness Š 2.5 mm
– for packages with a thickness < 2.5 mm and a volume
process) for packages with a thickness < 2.5 mm and a
volume < 350 mm
turbulent wave with high upward pressure followed by a
smooth laminar wave.
– larger than or equal to 1.27 mm, the footprint
– smaller than 1.27 mm, the footprint longitudinal axis
The footprint must incorporate solder thieves at the
downstream end.
be placed at a 45 angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
 350 mm
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
must be parallel to the transport direction of the
printed-circuit board.
3
so called thick/large packages.
3
so called small/thin packages.
Product specification
TDA1519C

Related parts for TDA1519C