LPC2387FBD100 NXP Semiconductors, LPC2387FBD100 Datasheet - Page 11

• Manufacturer Part Number: LPC2387FBD100
• Description: The LPC2387 is an ARM7 microcontroller for embedded applications featuring a high level of integration and low power consumption at frequencies of 72 MHz
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC2387
Product data sheet
Symbol
P2[4]/PWM1[5]/
DSR1/TRACESYNC
P2[5]/PWM1[6]/
DTR1/TRACEPKT0
P2[6]/PCAP1[0]/RI1/
TRACEPKT1
P2[7]/RD2/
RTS1/TRACEPKT2
P2[8]/TD2/
TXD2/TRACEPKT3
P2[9]/
USB_CONNECT/
RXD2/EXTIN0
P2[10]/EINT0
P2[11]/EINT1/
MCIDAT1/
I2STX_CLK
P2[12]/EINT2/
MCIDAT2/
I2STX_WS
Pin description
Pin
69
68
67
66
65
64
53
52
51
[1]
[1]
[1]
[1]
[1]
[1]
[6]
[6]
[6]
…continued
Type
I/O
O
I
O
I/O
O
O
O
I/O
I
I
O
I/O
I
O
O
I/O
O
O
O
I/O
O
I
I
I/O
I
I/O
I
O
I/O
I/O
I
O
I/O
All information provided in this document is subject to legal disclaimers.
Description
P2[4] — General purpose digital input/output pin.
PWM1[5] — Pulse Width Modulator 1, channel 5 output.
DSR1 — Data Set Ready input for UART1.
TRACESYNC — Trace Synchronization.
P2[5] — General purpose digital input/output pin.
PWM1[6] — Pulse Width Modulator 1, channel 6 output.
DTR1 — Data Terminal Ready output for UART1.
TRACEPKT0 — Trace Packet, bit 0.
P2[6] — General purpose digital input/output pin.
PCAP1[0] — Capture input for PWM1, channel 0.
RI1 — Ring Indicator input for UART1.
TRACEPKT1 — Trace Packet, bit 1.
P2[7] — General purpose digital input/output pin.
RD2 — CAN2 receiver input.
RTS1 — Request to Send output for UART1.
TRACEPKT2 — Trace Packet, bit 2.
P2[8] — General purpose digital input/output pin.
TD2 — CAN2 transmitter output.
TXD2 — Transmitter output for UART2.
TRACEPKT3 — Trace Packet, bit 3.
P2[9] — General purpose digital input/output pin.
USB_CONNECT — Signal used to switch an external 1.5 k resistor under
software control. Used with the SoftConnect USB feature.
RXD2 — Receiver input for UART2.
EXTIN0 — External Trigger Input.
P2[10] — General purpose digital input/output pin.
Note: LOW on this pin while RESET is LOW forces on-chip bootloader to take
over control of the part after a reset.
EINT0 — External interrupt 0 input.
P2[11] — General purpose digital input/output pin.
EINT1 — External interrupt 1 input.
MCIDAT1 — Data line for SD/MMC interface.
I2STX_CLK — Transmit Clock. It is driven by the master and received by the
slave. Corresponds to the signal SCK in the I
P2[12] — General purpose digital input/output pin.
EINT2 — External interrupt 2 input.
MCIDAT2 — Data line for SD/MMC interface.
I2STX_WS — Transmit Word Select. It is driven by the master and received by
the slave. Corresponds to the signal WS in the I
Rev. 5 — 9 January 2012
2
S-bus specification.
Single-chip 16-bit/32-bit MCU
2
S-bus specification.
LPC2387
© NXP B.V. 2012. All rights reserved.
11 of 66