MAX4907F Maxim, MAX4907F Datasheet
MAX4907F
Available stocks
Related parts for MAX4907F
MAX4907F Summary of contents
Page 1
... The MAX4906/MAX4906F feature two single-pole/dou- ble-throw (SPDT) switches, and the MAX4907/ MAX4907F feature two single-pole/single-throw switches (SPST). The MAX4907/MAX4907F have a low 7Ω (max) on-resistance and 7pF (max) on-capacitance. These devices are fully specified to operate from a single +3.0V to +3.6V power supply and are protected against a +5 ...
Page 2
... Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
... 1MHz, Figure 2 (Note 7) (OFF) MAX4906ELB, MAX4906FELB f = 1MHz, Figure 2 C (ON) (Note 7) MAX4907ELA, MAX4907FELA MAX4906ELB, MAX4906FELB 1MHz (Note 7) ONM MAX4907ELA, MAX4907FELA 1. 300Ω / 1.5V ...
Page 4
... Operating Supply-Voltage Range Quiescent Supply Current Quiescent Supply Current During Shutdown Note 2: All units are 100% production tested at T and not production tested. Note 3: The switch will turn off for voltages above (V (MAX4906F/MAX4907F). Note 4: Δ ON(MAX) ON(CH1) – ON(CH2) Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance, as measured over specified analog signal ranges ...
Page 5
High-/Full-Speed USB 2.0 Switches (T = +25°C, unless otherwise noted.) A CHARGE INJECTION vs. V COM 100pF 3. 1.1 2.2 VCOM (V) LOGIC THRESHOLD vs. SUPPLY VOLTAGE 1 ...
Page 6
High-/Full-Speed USB 2.0 Switches (T = +25°C, unless otherwise noted.) A OUTPUT SKEW BETWEEN SWITCHES vs. SUPPLY VOLTAGE -10 3.0 3.2 SUPPLY VOLTAGE (V) 6 _______________________________________________________________________________________ Typical Operating Characteristics (continued) FREQUENCY RESPONSE 0 -10 ON-LOSS -20 ...
Page 7
... IN_ MAX4906/MAX4906F NC1 MAX4907/MAX4907F 50Ω GND MEASUREMENTS ARE STANDARDIZED AGAINST SHORTS AT IC TERMINALS. OFF-ISOLATION IS MEASURED BETWEEN COM_ AND "OFF" NO_ OR NC_ TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM_ AND "ON" NO_ OR NC_ TERMINAL ON EACH SWITCH. CROSSTALK IS MEASURED FROM ONE CHANNEL TO THE OTHER CHANNEL. ...
Page 8
... INPUT C INCLUDES FIXTURE AND STRAY CAPACITANCE OUT Figure 3. Switching Time 8 _______________________________________________________________________________________ Test Circuits/Timing Diagrams (continued) V+ 10nF V+ COM_ MAX4906/MAX4906F MAX4907/MAX4907F IN NC_ or NO_ GND V+ LOGIC V+ INPUT COM_ V OUT SWITCH OUTPUT < 5ns < 5ns ...
Page 9
... High-/Full-Speed USB 2.0 Switches MAX4906/MAX4906F MAX4907/MAX4907F NC1 NO1 IN+ NC2 NO2 IN IN+ 50 50% IN PLHX V+ V OUT+ 50 50% V OUT PHLY Figure 4. Output Signal Skew, Rise/Fall Time, Propagation Delay _______________________________________________________________________________________ _______________________________________________________________________________________ Test Circuits/Timing Diagrams (continued) COM1 ...
Page 10
... IN The MAX4906/MAX4906F/MAX4907/MAX4907F are fully specified to operate from a single +3.0V to +3.6V supply and are available with +5.5V fault protection (MAX4906F/ MAX4907F). When operating from a +3.0V to +3.6V sup- ply, the low threshold of these devices permits them to be used with logic levels as low as 1.4V.The MAX4906/MAX4906F/MAX4907/MAX4907F are based on a charge-pump-assisted n-channel architecture and thus operate at 300µ ...
Page 11
... Analog Signal Levels The on-resistance of the MAX4906/MAX4906F/ MAX4907/MAX4907F is very low and stable as the ana- log input signals are swept from ground to V+ (see the Typical Operating Characteristics). These switches are bidirectional, allowing NO_, NC_, and COM_ to be con- figured as either inputs or outputs ...
Page 12
... GND USB The wide bandwidth of the MAX4906/MAX4906F/ CONNECTOR MAX4907/MAX4907F meets the needs of 10/100 Ethernet switching. These devices switch the signals from two interface transformers and connect the signals to a single 10/100 Base-T Ethernet PHY, simplifying docking station design and reducing manufacturing costs. ...
Page 13
... COM1 3 MAX4907F COM2 4 μDFN Revision History Pages changed at Rev 11, 14 ______________________________________________________________________________________ PART MAX4906ELB 8 IN MAX4906FELB 7 V+ MAX4907ELA 6 NO1 MAX4907FELA 5 NO2 PROCESS: BiCMOS Selector Guide FAULT TOP CONFIGURATION PROTECTION MARK Dual SPDT NO AAB Dual SPDT YES AAA Dual SPST NO AAE ...
Page 14
... L822-1 L1022-1 -DRAWING NOT TO SCALE- Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...