M25PX64-VME6E Numonyx, B.V., M25PX64-VME6E Datasheet - Page 50
M25PX64-VME6E
Manufacturer Part Number
M25PX64-VME6E
Description
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer
Numonyx, B.V.
Datasheet
1.M25PX64-VME6E.pdf
(66 pages)
- Current page: 50 of 66
- Download datasheet (2Mb)
Instructions
6.17
50/66
Bulk erase (BE)
The bulk erase (BE) instruction sets all bits to ‘1’ (FFh). Before it can be accepted, a write
enable (WREN) instruction must previously have been executed. After the write enable
(WREN) instruction has been decoded, the device sets the write enable latch (WEL).
The bulk erase (BE) instruction is entered by driving Chip Select (S) Low, followed by the
instruction code on serial data input (DQ0). Chip Select (S) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the bulk erase instruction is not executed. As soon as Chip Select (S)
is driven High, the self-timed bulk erase cycle (whose duration is t
bulk erase cycle is in progress, the status register may be read to check the value of the
write in progress (WIP) bit. The write in progress (WIP) bit is 1 during the self-timed bulk
erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is
completed, the write enable latch (WEL) bit is reset.
The bulk erase (BE) instruction is executed only if all block protect (BP2, BP1, BP0) bits are
0. The bulk erase (BE) instruction is ignored if one, or more, sectors are protected.
Figure 25. Bulk erase (BE) instruction sequence
S
C
DQ0
Figure
0
1
2
25.
Instruction
3
4
5
6
7
BE
AI13743
) is initiated. While the
M25PX64
Related parts for M25PX64-VME6E
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
16-Mbit, page-erasable serial flash memory with byte-alterability, 75 MHz SPI bus, standard pinout
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
512-Kbit, serial flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
128 Mbit (Multilevel), low-voltage, Serial Flash memory with 50-MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet:
Part Number:
Description:
2 Mbit, low voltage, Serial Flash memory with 50MHz SPI bus interface
Manufacturer:
Numonyx, B.V.
Datasheet: