DSPIC30F5016 Microchip Technology Inc., DSPIC30F5016 Datasheet - Page 12

• Manufacturer Part Number: DSPIC30F5016
• Description: Dspic30f5015/5016 Enhanced Flash 16-bit Digital Signal Controller
• Manufacturer: Microchip Technology Inc.

dsPIC30F5015/5016
TABLE 1-1:
DS70149C-page 10
MCLR
OCFA
OC1-OC4
OSC1
OSC2
PGD
PGC
RB0-RB15
RC13-RC15
RD0-RD11
RE0-RE7
RF0-RF6
RG2-RG3
RG6-RG9
SCK1
SDI1
SDO1
SS1
SCK2
SDI2
SDO2
SS2
SCL
SDA
SOSCO
SOSCI
T1CK
T4CK
U1RX
U1TX
V
V
V
V
Legend: CMOS = CMOS compatible input or output
REF
REF
DD
SS
Pin Name
+
-
ST
I
Type
I/O PIN DESCRIPTIONS FOR dsPIC30F5015 (CONTINUED)
Pin
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/P
I/O
I/O
= Schmitt Trigger input with CMOS levels
= Input
O
O
O
O
O
P
P
I
I
I
I
I
I
I
I
I
I
I
I
I
ST/CMOS
ST/CMOS
Analog
Analog
Buffer
Type
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
ST
—
—
—
—
—
—
—
—
Master Clear (Reset) input or programming voltage input. This pin is an active-
low Reset to the device.
Compare Fault A input (for Compare channels 1, 2, 3 and 4).
Compare outputs 1 through 4.
Oscillator crystal input. ST buffer when configured in RC mode; CMOS
otherwise.
Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator
mode. Optionally functions as CLKO in RC and EC modes.
In-Circuit Serial Programming™ data input/output pin.
In-Circuit Serial Programming clock input pin.
PORTB is a bidirectional I/O port.
PORTC is a bidirectional I/O port.
PORTD is a bidirectional I/O port.
PORTE is a bidirectional I/O port.
PORTF is a bidirectional I/O port.
PORTG is a bidirectional I/O port.
Synchronous serial clock input/output for SPI #1.
SPI #1 Data In.
SPI #1 Data Out.
SPI #1 Slave Synchronization.
Synchronous serial clock input/output for SPI #2.
SPI #2 Data In.
SPI #2 Data Out.
SPI #2 Slave Synchronization.
Synchronous serial clock input/output for I
Synchronous serial data input/output for I
32 kHz low-power oscillator crystal output.
32 kHz low-power oscillator crystal input. ST buffer when configured in RC
mode; CMOS otherwise.
Timer1 external clock input.
Timer4 external clock input.
UART1 Receive.
UART1 Transmit.
Positive supply for logic and I/O pins.
Ground reference for logic and I/O pins.
Analog Voltage Reference (High) input.
Analog Voltage Reference (Low) input.
Analog = Analog input
O
P
Description
= Output
= Power
2
2
C.
C™.
© 2007 Microchip Technology Inc.