MAX2036 Maxim Integrated Products, MAX2036 Datasheet - Page 2

• Manufacturer Part Number: MAX2036
• Description: Ultrasound VGA Integrated
• Manufacturer: Maxim Integrated Products

www.DataSheet4U.com
Ultrasound VGA Integrated
with CW Octal Mixer
ABSOLUTE MAXIMUM RATINGS
V
Any Other Pins to GND...............................-0.3V to (V
CW Mixer Output Voltage to GND (CW_IOUT+, CW_IOUT-,
VGA Differential Input Voltage (VGIN_+, VGIN_-)............8.0V
Analog Gain Control Differential Input Voltage
CW Mixer Differential Input Voltage
DC ELECTRICAL CHARACTERISTICS—VGA MODE
(Figure 7, V
or 1, TMODE = 0, PD = 0, CW_VG = 1, CW_M1 = 0, CW_M2 = 0, no RF signals applied, capacitance to GND at each of the VGA
differential outputs is 60pF, differential capacitance across the VGA outputs is 10pF, R
through four separate ±0.1% 115Ω resistors, all CW channels programmed off. Typical values are at V
unless otherwise noted.) (Note 2)
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
VGA MODE
Supply Voltage Range
V
Range
Total Power-Supply Current
V
V
Current Consumption per
Amplifier Channel
Differential Analog Control
Voltage Range
Differential Analog Control
Common-Mode Voltage
Analog Control Input Source/Sink
Current
LOGIC INPUTS
CMOS Input High Voltage
CMOS Input Low Voltage
CC
CC
CC
REF
CW_QOUT+, CW_QOUT-) ................................................13V
(VG_CTL+, VG_CTL-) ..................................................8.0V
(CWIN_+, CWIN_-).......................................................8.0V
, V
_______________________________________________________________________________________
External Reference Voltage
Supply Current
Current
REF
layer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
PARAMETER
to GND .................................................-0.3V to +5.5V
CC
= V
REF =
4.75V to 5.25V, V
SYMBOL
V
I
V
V
I
VCC
V
REF
V
REF
CC
CM
CM
IH
IL
= (3/5)V
(Note 3)
Refers to V
current plus V
Refers to V
Minimum gain
Maximum gain
CC
REF
+ 0.3V)
, T
A =
P-P
P-P
P-P
CC
CC
0°C to +70°C, V
REF
supply
supply current
CONDITIONS
current
CW Mixer LVDS LO Differential Input Voltage..................8.0V
Continuous Power Dissipation (T
Operating Temperature Range...............................0°C to +70°C
Junction Temperature ......................................................+150°C
θ
θ
Storage Temperature Range .............................-40°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
JC
JA
100-Pin TQFP (derated 45.5mW/°C above +70°C)..3636.4mW
(Note 1)....................................................................+22°C/W
(Note 1) .....................................................................+2°C/W
GND
PD = 0
PD =1
= 0, LOW_PWR = 0, M4_EN = 0, CW_FILTER = 0
L =
1kΩ, CW mixer outputs pulled up to +11V
4.75
4.75
2.85
MIN
2.3
A
CC
= +70°C)
TYP
= V
204
192
4.5
+2
27
12
24
-2
5
5
3
REF
= 5V, T
MAX
5.25
5.25
3.15
231
216
0.8
33
15
27
5
A
= +25°C,
UNITS
V
mA
mA
mA
mA
mA
V
V
P-P
V
V
V
P-P