ADP315PC87570 National Semiconductor, ADP315PC87570 Datasheet - Page 118
ADP315PC87570
Manufacturer Part Number
ADP315PC87570
Description
Keyboard and Power Management Controller
Manufacturer
National Semiconductor
Datasheet
1.ADP315PC87570.pdf
(168 pages)
- Current page: 118 of 168
- Download datasheet (892Kb)
Bits 2-0 - Main Clock Divide (MDIV)
Defines the pre-scale ratio of the input clock. The pre-scale
ratio is 2
viding a pre-scale ratio of 1 to 32. Table Figure 15-1 sum-
marizes MDIV allowed values.
15.6.3 TWD Timer 0 Register (TWDT0)
The TWDT0 Register is a read/write register. It defines the
T0OUT interrupt rate. Upon reset, this register is initialized
to FFFFh.
Bits 7-0 - PRESET
15.6.4 TWDT0 Control and Status Register (T0CSR)
The T0CSR Register is a read/write register. It controls the
operation and provides the status of the T0 timer. The non-
reserved bits of T0CSR are cleared (0) on reset.
Bit 0 - Restart (RST)
Bit 1 - Terminal Count (TC)
7
7
Defines the counter preset value. Whenever the counter
reaches zero, it starts counting down from this value.
The T0OUT frequency is the T0IN frequency divided by
(PRESET+1). The allowed values of the PRESET field
are 0001h through FFFFh.
When set (1), forces the timer to restart counting in the
next input clock rising edge. The bit is cleared by the in-
put clock rising edge, indicating that the counter re-
sumed its automatic re-triggerable operation. Writing 0
to this bit is ignored.
The TC bit indicates that the counter has reached zero (ter-
minal count). This bit is cleared each time the register is
read. It is a read only bit and data written to it is ignored.
MDIV
. MDIV must be in the range of zero to five, pro-
Reserved
Table 15-1. MDIV Values
MDIV
Other Reserved
000
001
010
011
100
101
1:1
1:2
1:4
1:8
1:16
1:32
PRESET
Clock Ratio
2
TC
1
Timer and WATCHDOG (TWD)
RST
0
0
118
15.6.5 WATCHDOG Count Register (WDCNT)
The WDCNT Register is a byte wide, write only register. It
holds the value loaded into the WATCHDOG counter when it
is serviced, and counts down from it. The WATCHDOG is
started by the first write to the register. Each successive write
restarts the WATCHDOG count. Upon reset this register is ini-
tialized to 0Fh.
Bits 7-0 - PRESET
15.6.6 WATCHDOG Service Data Match Register
The WDSDM Register is an 8-bit write only register. When
TWCFG.WDSDME is set, the WATCHDOG counting re-
starts from the value in WDCNT, when WDSDM is written
with 5Ch. If any other data is written to this register, it trig-
gers a WATCHDOG signal. If RSDATA is written for a sec-
ond time before one WATCHDOG clock has occurred, this
also triggers a WATCHDOG signal. Any write to this register
when TWCFG.WDSDME is cleared is ignored.
Bits 7-0 - Restart Data (RSDATA)
15.7 USAGE HINTS
The TWD protects WATCHDOG operation from software
tampering. To achieve the highest level of protection, pro-
ceed as follows:
1. Program the TWDT0 pre-scale and TMWT0 timers to
2. Configure the WATCHDOG clock to use T0IN or T0OUT
3. Program the WDCTL to the maximum period between
4. Configure the WATCHDOG to use data match, and lock
5. Touch the WATCHDOG by writing 5Ch to WDSDM at
7
7
Defines the counter preset value. Whenever the counter
reaches zero, it starts counting down from this value.
The T0OUT frequency is the T0IN frequency divided by
(PRESET+1). The allowed values of the PRESET field
are 0001h through FFFFh.
the desired values.
using TWCFG.WDCT0I bit.
WATCHDOG touch operations. Note that from this point,
the WATCHDOG starts operating and must be touched
periodically to prevent a WATCHDOG error signal.
all the TWD configuration and setting registers by set-
ting bits 0 through 4 and bit 6 of the WDCFG.
the appropriate rate (i.e., no more than once every
WATCHDOG clock cycle and no less than the period
programmed to WDCTL).
(WDSDM)
PRESET
RSDATA
www.national.com
0
0
Related parts for ADP315PC87570
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
National Semiconductor [8-Bit D/A Converter]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
National Semiconductor [Media Coprocessor]
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Digitally Controlled Tone and Volume Circuit with Stereo Audio Power Amplifier, Microphone Preamp Stage and National 3D Sound
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
AC97 Rev 2 Codec with Sample Rate Conversion and National 3D Sound
Manufacturer:
National Semiconductor
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
General Purpose, Low Voltage, Low Power, Rail-to-Rail Output Operational Amplifiers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
8-bit 20 MSPS flash A/D converter.
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Low Noise Quad Operational Amplifier
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad Differential Line Receivers
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal? Bus Transceiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
Dual Line Receiver
Manufacturer:
National Semiconductor
Datasheet:
Part Number:
Description:
TTL to 10k ECL Level Translator with Latch
Manufacturer:
National Semiconductor
Datasheet: