UPD78F0138 NEC, UPD78F0138 Datasheet - Page 186
UPD78F0138
Manufacturer Part Number
UPD78F0138
Description
(UPD78xxxx) 8-Bit Single-Chip Microcontrollers
Manufacturer
NEC
Datasheet
1.UPD78F0138.pdf
(558 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
UPD78F0138M1GK-9ET
Manufacturer:
NEC
Quantity:
115
Part Number:
UPD78F0138M5GB
Manufacturer:
NEC
Quantity:
20 000
- Current page: 186 of 558
- Download datasheet (5Mb)
(8) Timer operation
(9) Capture operation
(10) Compare operation
(11) Edge detection
186
<1> Even if 16-bit timer counter 0n (TM0n) is read, the value is not captured by 16-bit timer capture/compare
<2> Regardless of the CPU’s operation mode, when the timer stops, the input signals to the TI00n/TI01n pins
<3> The one-shot pulse output mode operates correctly only in the free-running mode and the mode in which
<1> If TI00n valid edge is specified as the count clock, a capture operation by the capture register specified as
<2> To ensure the reliability of the capture operation, the capture trigger requires a pulse two cycles longer than
<3> The capture operation is performed at the falling edge of the count clock. An interrupt request input
A capture operation may not be performed for CR00n/CR01n set in compare mode even if a capture trigger has
been input.
<1> If the TI00n or TI01n pin is high level immediately after system reset and the rising edge or both the rising
<2> The sampling clock used to remove noise differs when the TI00n valid edge is used as the count clock and
register 01n (CR01n).
are not acknowledged.
clear & start occurs at the TI00n valid edge. In the mode in which clear & start occurs on a match between
the TM0n register and CR00n register, one-shot pulse output is not possible because an overflow does not
occur.
the trigger for TI00n is not possible.
the count clock selected by prescaler mode register 0n (PRM0n).
(INTTM00n/INTTM01n), however, is generated at the rise of the next count clock.
and falling edges are specified as the valid edge of the TI00n or TI01n pin to enable the 16-bit timer counter
0n (TM0n) operation, a rising edge is detected immediately after the operation is enabled. Be careful
therefore when pulling up the TI00n or TI01n pin. However, the rising edge is not detected at restart after
the operation has been stopped once.
when it is used as a capture trigger. In the former case, the count clock is f
count clock is selected by prescaler mode register 0n (PRM0n). The capture operation is started only after
a valid edge is detected twice by sampling, thus eliminating noise with a short pulse width.
Remark n = 0:
n = 0, 1:
CHAPTER 6 16-BIT TIMER/EVENT COUNTERS 00 AND 01
µ
µ
PD780131, 780132
PD780133, 780134, 78F0134, 780136, 780138, 78F0138
User’s Manual U16228EJ2V0UD
X
, and in the latter case the
Related parts for UPD78F0138
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16BIT MCU, 128K FLASH, 8K RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT UC, 32K FLASH, 1KB RAM, LCD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 60K FLASH, 3KB RAM, CAN
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 128K FLASH, 7K RAM, LQFP
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
8BIT MCU, 4K FLASH, 128B RAM, SMD
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet: