FDC37M81x SMSC Corporation, FDC37M81x Datasheet - Page 20
FDC37M81x
Manufacturer Part Number
FDC37M81x
Description
PC98/99 Compliant Enhanced Super I/O Controller
Manufacturer
SMSC Corporation
Datasheet
1.FDC37M81X.pdf
(198 pages)
- Current page: 20 of 198
- Download datasheet (683Kb)
DIGITAL OUTPUT REGISTER (DOR)
Address 3F2 READ/WRITE
The DOR controls the drive select and motor enables of the disk interface outputs. It also contains the
enable for the DMA logic and a software reset bit. The contents of the DOR are unaffected by a software
reset. The DOR can be written to at any time.
BIT 0 and 1 DRIVE SELECT
These two bits are binary encoded for the drive
selects, thereby allowing only one drive to be
selected at one time.
BIT 2 nRESET
A logic "0" written to this bit resets the Floppy disk
controller. This reset will remain active until a logic
"1" is written to this bit. This software reset does
not affect the DSR and CCR registers, nor does it
affect the other bits of the DOR register.
minimum reset duration required is 100ns,
therefore toggling this bit by consecutive writes to
this register is a valid method of issuing a software
reset.
BIT 3 DMAEN
PC/AT and Model 30 Mode:
Writing this bit to logic "1" will enable the DRQ,
nDACK, TC pins and interrupt functions. This bit
being a logic "0" will disable the nDACK, TC inputs
and interrupt functions, and hold the DRQ output
in a high impedance state. This bit is a logic "0"
after a reset and in these modes.
PS/2 Mode: In this mode the DRQ, nDACK, TC
pins and interrupt functions are always enabled.
During a reset, the DRQ, nDACK, TC, and FINTR
pins will remain enabled, but this bit will be cleared
to a logic "0".
RESET
COND.
MOT
EN3
7
0
MOT
EN2
6
0
MOT
EN1
5
0
The
MOT
EN0
20
4
0
BIT 4 MOTOR ENABLE 0
This bit controls the MTR0 disk interface output. A
logic "1" in this bit will cause the output pin to go
active.
BIT 5 MOTOR ENABLE 1
This bit controls the MTR1 disk interface output. A
logic "1" in this bit will cause the output pin to go
active.
BIT 6 MOTOR ENABLE 2
The MTR2 disk interface output is not supported in
the FDC37M81x.
BIT 7 MOTOR ENABLE 3
The MTR3 disk interface output is not supported in
the FDC37M81x.
DMAEN nRESE
3
0
Table 3 - Drive Activation Values
DRIVE
0
1
2
T
0
DRIVE
SEL1
1
0
DOR VALUE
DRIVE
SEL0
1CH
2DH
0
0
Related parts for FDC37M81x
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EMC Filters - Single-Phase Filters - FD/FDC/FDV IEC Connector Filter
Manufacturer:
Premo
Datasheet:
Part Number:
Description:
FD TYPE CONNECTOR FOR RIBBON CABLE
Manufacturer:
Hirose Electric
Datasheet:
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: