ds2155gt-r Maxim Integrated Products, Inc., ds2155gt-r Datasheet - Page 108
ds2155gt-r
Manufacturer Part Number
ds2155gt-r
Description
Ds2155 T1/e1/j1 Single-chip Transceiver
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.DS2155GT-R.pdf
(238 pages)
- Current page: 108 of 238
- Download datasheet (2Mb)
19.2.1 T1 Mode
If the user selects to apply a 2.048MHz clock to the TSYSCLK pin, then the data input at TSER is
ignored every fourth channel. Therefore channels 1, 5, 9, 13, 17, 21, 25, and 29 (time slots 0, 4, 8, 12, 16,
20, 24, and 28) are ignored. The user can supply frame or multiframe sync pulse to the TSSYNC input.
Also, in 2.048MHz applications, the TCHBLK output is forced high during the channels ignored by the
framer.
19.2.2 E1 Mode
A 1.544MHz or 2.048MHz clock can be applied to the TSYSCLK input. The user must supply a frame
sync pulse or a multiframe sync pulse to the TSSYNC input.
19.3 Elastic Stores Initialization
There are two elastic store initializations that can be used to improve performance in certain applications,
elastic store reset and elastic store align. Both of these involve the manipulation of the elastic store’s read
and write pointers and are useful primarily in synchronous applications (RSYSCLK/TSYSCLK are
locked to RCLK/TCLK, respectively)
Table 19-A. Elastic Store Delay After Initialization
19.4 Minimum Delay Mode
Elastic store minimum delay mode can be used when the elastic store’s system clock is locked to its
network clock (i.e., RCLK locked to RSYSCLK for the receive side and TCLK locked to TSYSCLK for
the transmit side). ESCR.5 and ESCR.1 enable the transmit and receive elastic store minimum delay
modes. When enabled, the elastic stores are forced to a maximum depth of 32 bits instead of the normal
two-frame depth. This feature is useful primarily in applications that interface to a 2.048MHz bus.
Certain restrictions apply when minimum delay mode is used. In addition to the restriction mentioned
above, RSYNC must be configured as an output when the receive elastic store is in minimum delay
mode; TSYNC must be configured as an output when transmit minimum delay mode is enabled. In a
typical application, RSYSCLK and TSYSCLK are locked to RCLK, and RSYNC (frame output mode) is
connected to TSSYNC (frame input mode). All of the slip contention logic in the framer is disabled (since
slips cannot occur). On power-up, after the RSYSCLK and TSYSCLK signals have locked to their
respective network clock signals, the elastic store reset bits (ESCR.2 and ESCR.6) should be toggled
from a 0 to a 1 to ensure proper operation.
Receive Elastic Store Reset
Transmit Elastic Store Reset
Receive Elastic Store Align
Transmit Elastic Store Align
INITIALIZATION
REGISTER BIT
ESCR.2
ESCR.6
ESCR.3
ESCR.7
(Table
19-A).
8 Clocks < Delay < 1 Frame
1 Frame < Delay < 2 Frames
½ Frame < Delay < 1 ½ Frames
½ Frame < Delay < 1 ½ Frames
108 of 238
DELAY
Related parts for ds2155gt-r
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
power light source Luxeon Line
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
Nonvolatile Ram Controller Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.3v Single-piece 8mb Nonvolatile Sram Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Pon Triplexer Control And Monitoring Circuit Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ttl Compatible Cmos Analog Switches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Improved Low-power, Cmos Analog Switches With Latches Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
4a, 20ns, Dual Mosfet Drivers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Nicd/nimh Battery Fast-charge Controllers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
3.6v, 1w Autoramping Power Amplifier For 900mhz Applications Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
2.7v, Single-supply, Cellular-band Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
5ghz Linear Power Amplifiers Integrated Products
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Evaluation Kits for the MAX3514
Manufacturer:
Maxim Integrated Products, Inc.
Part Number:
Description:
Accurate I2c Rtc With Integrated Tcxo/crystal/fram
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Ds1863 Burst-mode Pon Controller With Integrated Monitoring
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet: