ds8023-rrx Maxim Integrated Products, Inc., ds8023-rrx Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
ds8023-rrx
Manufacturer Part Number
ds8023-rrx
Description
Smart Card Interface
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.DS8023-RRX.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ds8023-rrx+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Smart Card Interface
The DS8023 card interface remains inactive no matter
the levels on the command lines until duration t
V
When V
card deactivation sequence if its card interface is active.
The clock signal from the DS8023 to the smart card
(CLK) is generated from the clock input on XTAL1 or
from a crystal operating at up to 20MHz connected
between pins XTAL1 and XTAL2. The inputs CLKDIV1
and CLKDIV2 determine the frequency of the CLK sig-
nal, which can be f
Table 1 shows the relationship between CLKDIV1 and
CLKDIV2 and the frequency of CLK.
Do not change the state of pins CLKDIV1 and CLKDIV2
simultaneously; a delay of 10ns minimum between
changes is required. The minimum duration of any state
of CLK is 8 periods of XTAL1.
The hardware in the DS8023 guarantees that the fre-
quency change is synchronous. During a transition of
the clock divider, no pulse is shorter than 45% of the
smallest period, and the clock pulses before and after
the instant of change have the correct width.
To achieve a 45% to 55% duty factor on pin CLK when
no crystal is present, the input signal on XTAL1 should
have a 48% to 52% duty factor. Transition time on
XTAL1 should be less than 5% of the period.
With a crystal, the duty factor on pin CLK may be 45%
to 55% depending on the circuit layout and on the crys-
tal characteristics and frequency.
The DS8023 crystal oscillator runs when the device is
powered up. If the crystal oscillator is used or the clock
pulse on pin XTAL1 is permanent, the clock pulse is
applied to the card at time t
the signal applied to XTAL1 is controlled by the host
microcontroller, the clock pulse is applied to the card
when it is sent by the system microcontroller (after
completion of the activation sequence).
Table 1. Clock Frequency Selection
8
DD
_______________________________________________________________________________________
CLKDIV1
has reached a level higher than V
DD
0
0
1
1
falls below V
XTAL
CLKDIV2
TH2
, f
0
1
1
0
XTAL/2
4
, the DS8023 executes a
(see Figures 7 and 8). If
Clock Circuitry
, f
XTAL/4
TH2
, or f
f
f
f
XTAL
XTAL
XTAL
f
f
XTAL
CLK
+ V
/8
/4
/2
XTAL/8
W
HYS2
after
.
.
The three data lines I/O, AUX1, and AUX2 are identical.
This section describes the characteristics of I/O and
I/OIN, but also applies to AUX1, AUX1IN, AUX2, and
AUX2IN.
I/O and I/OIN are pulled high with an 11kΩ resistor (I/O
to V
side of the transceiver to receive a falling edge
becomes the master. When the master is decided, the
opposite side switches to slave mode, ignoring subse-
quent edges until the master releases. After a time delay
t
thus transmitting the logic 0 present on the master side.
When the master side asserts a logic 1, a p transistor
on the slave side is activated during the time delay,
t
up) states. This active pullup provides fast low-to-high
transitions. After the duration of t
depends only on the internal pullup resistor and the
load current. Current to and from the card I/O lines is
limited internally to 15mA. The maximum frequency on
these lines is 1MHz.
The DS8023 powers up with the card interface in the
inactive mode. Minimal circuitry is active while waiting
for the host to initiate a smart card session.
After power-on and the reset delay, the host microcon-
troller can monitor card presence with signals OFF and
CMDVCC, as shown in Table 2.
Table 2. Card Presence Indication
D(EDGE)
PU
• All card contacts are inactive (approximately 200Ω
• Pins I/OIN, AUX1IN, and AUX2IN are in the high-
• Voltage generators are stopped.
• XTAL oscillator is running (if included in the device).
• Voltage supervisor is active.
• The internal oscillator is running at its low frequency.
, and then both sides return to their inactive (pulled
CC
to GND).
impedance state (11kΩ pullup resistor to V
High
OFF
Low
and I/OIN to V
, an n transistor on the slave side is turned on,
DD
Activation Sequence
CMDVCC
) in the inactive state. The first
High
High
I/O Transceivers
Inactive Mode
PU
, the output voltage
Card present.
Card not present.
STATUS
DD
).