tda9899 NXP Semiconductors, tda9899 Datasheet
tda9899
Available stocks
Related parts for tda9899
tda9899 Summary of contents
Page 1
... TDA9899 Multistandard hybrid IF processing including car mobile Rev. 03 — 15 January 2008 1. General description The Integrated Circuit (IC) is suitable for Intermediate Frequency (IF) processing including global multistandard Analog TV (ATV), Digital Video Broadcast (DVB) and mono FM radio using only 1 IC and fixed Surface Acoustic Waves (SAWs) (application dependent). ...
Page 2
... All DVB bandwidth ranges supported (including ZIF I/Q) I TAGC detector for independent tuner gain control loop applications TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile 2 C-bus 2 C-bus or alternatively by potentiometer Rev. 03 — 15 January 2008 TDA9899 2 C-bus © NXP B.V. 2008. All rights reserved 103 ...
Page 3
... VIF(dah) frequency window TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile Conditions lower limit video output signal see Table 26 related to f VIF all standards except M/N M/N standard Rev. 03 — 15 January 2008 TDA9899 2 C-bus Min Typ Max Unit [1] 4.5 5.0 5 190 ...
Page 4
... Figure 9 AFC TV mode FM: QSS or TSS mode; 27 kHz FM deviation de-emphasis AM modulation FM de-emphasis; FM deviation: for TV mode 27 kHz and for radio mode 22.5 kHz AM modulation; BP on; see Figure 32 Rev. 03 — 15 January 2008 TDA9899 Min Typ Max Unit [2] 1.7 2.0 2.3 V [ [2][4] ...
Page 5
... Rev. 03 — 15 January 2008 Min Typ 80 100 Figure 140 Figure 14 [6] 0.85 1. [7] - 1.0 - 0. TDA9899 Max Unit - kHz - 180 300 mV 1.25 A/kHz - dB 1 © NXP B.V. 2008. All rights reserved 103 ...
Page 6
... Table [ [ [8] 98 102 [8] 115 119 [11 150 Table 25. In this way the full composite video TDA9899 Max Unit - MHz - dBc/Hz - dBc/Hz - dBc/Hz - dBc/Hz 2.7 dB 2 dBc/ MHz - dBc/Hz - ...
Page 7
... L Description plastic low profile quad flat package; 48 leads; body 7 plastic thermal enhanced very thin quad flat package; no leads; 48 terminals; body 7 7 0.85 mm Rev. 03 — 15 January 2008 TDA9899 Figure = 45 MHz to 60 MHz and 1.4 mm © NXP B.V. 2008. All rights reserved. ...
Page 8
... IF1B 2 9 IF2A 10 IF2B CIFAGC 5 45 AGCVIN DECODER PEAK AGC TUNER 47 TAGC 48 GND Fig 1. Block diagram of TDA9899 (continued in TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile i.c. i.c. ADRSEL BVS GNDD C-BUS AM average SIF AGC FM peak VIF AGC ...
Page 9
... BAND-PASS FILTER (1) Optional. (2) Connect resistor if input or crystal is not used. Fig 2. Block diagram of TDA9899 (continued from TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile R (2) EXTERNAL SOUND (1) BAND-PASS FILTER EXTFILO EXTFILI on/off FM switch ...
Page 10
... Multistandard hybrid IF processing including car mobile LFSYN2 1 n.c. 2 IF3A 3 IF3B 4 CIFAGC 5 IF1A 6 TDA9899HL IF1B 7 CTAGC 8 IF2A 9 IF2B 10 TOP2 11 MPP1 12 Rev. 03 — 15 January 2008 TDA9899 36 AGCDIN 35 APCLC 34 APCHC 33 CVBS 32 BVS 31 AUD 30 OUT2B 29 OUT2A 28 CAF 27 OUT1B 26 OUT1A 25 ADRSEL 008aaa031 © NXP B.V. 2008. All rights reserved. ...
Page 11
... VIF AGC monitor output or port function 13 loop filter VIF PLL 14 internally connected; connect to ground 15 output to external filter 16 multipurpose pin 2: SIF AGC or FM AGC or TAGC or VIF AFC or FM AFC or WAFP monitor output 17 input from external filter Rev. 03 — 15 January 2008 TDA9899 36 AGCDIN 35 APCLC 34 APCHC 33 CVBS 32 BVS 31 AUD ...
Page 12
... AGC input for VIF amplifi MHz reference input or output 47 TAGC output 48 ground; plateau connection Rev. 03 — 15 January 2008 TDA9899 © NXP B.V. 2008. All rights reserved 103 ...
Page 13
... VIF AGC read out via I (TOP setting either via I TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile 2 C-bus (for IF level indication) with zero-calibration via TOP setting 2 C-bus or via TOP potentiometer). Rev. 03 — 15 January 2008 TDA9899 © NXP B.V. 2008. All rights reserved 103 ...
Page 14
... PLL gating mode for positive and negative modulation, optional. PLL optimized for either overmodulation or strong multipath (car mobile). TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile Rev. 03 — 15 January 2008 TDA9899 © NXP B.V. 2008. All rights reserved 103 ...
Page 15
... Weak signal processing for FM sound in the event of low or noisy FM carrier. Weak signal processing includes noise dependent gain and bandwidth control. TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile Rev. 03 — 15 January 2008 TDA9899 © NXP B.V. 2008. All rights reserved 103 ...
Page 16
... Table Rev. 03 — 15 January 2008 2 C-bus voltages. Pin ADRSEL A0 1 GND resistor to GND 0 resistor TDA9899 © NXP B.V. 2008. All rights reserved 103 ...
Page 17
... FM AGC detection AFC[4:1] automatic frequency control; see PONR power-on reset 1 = after power-on reset or after supply breakdown 0 = after a successful reading of the status register Rev. 03 — 15 January 2008 TDA9899 BYTE 2 A BYTE data (R1) data (R2 START condition ...
Page 18
... DIF AGC in DTV mode; see Rev. 03 — 15 January 2008 [1] AFC1 R1[ VAGC3 VAGC2 Table 11 TDA9899 [ 187.5 kHz) nom f 162.5 kHz nom f 137.5 kHz nom f 112.5 kHz nom f 87.5 kHz nom f 62.5 kHz nom f 37.5 kHz nom f 12.5 kHz nom ...
Page 19
... Rev. 03 — 15 January 2008 TDA9899 Figure 10) Typical V AGC(VIF) VAGC1 VAGC0 (V) R2[1] R2[ (TOP 0.36 ...
Page 20
... A BYTE 2 A BYTE bits subaddress Rev. 03 — 15 January 2008 TDA9899 Figure 10) VAGC1 VAGC0 R2[1] R2[ ...
Page 21
... FMWIDE1 SIFLEVEL VIDLEVEL OPSTATE 0 0 EASY3 TAGCTC TOPNEG4 TOPNEG3 XPOTPOS TOPPOS4 TOPPOS3 Rev. 03 — 15 January 2008 TDA9899 Mode subaddress for register W1 subaddress for register W2 subaddress for register W3 subaddress for register W4 subaddress for register W5 subaddress for register W6 subaddress for register W7 ...
Page 22
... Table 25 and bits FSFREQ[1:0] are described in Rev. 03 — 15 January 2008 TV1 DUAL FM and Table 20 Table 23 [1] f Sound BP FMPLL (MHz) W1[3] 1 4.5 M/N standard 1 5.5 B/G standard 1 6.0 I standard 1 6.5 D/K standard 1 off L/L-accent standard Table 36. TDA9899 0 EXTFIL © NXP B.V. 2008. All rights reserved 103 ...
Page 23
... Table 25 and for BP refer to Table 31. Input signal selection Signal at OUT1A and OUT1B (input switch) (output switch) internal BP via FM AGC internal BP internal BP external BP via FM AGC internal BP internal BP external BP Rev. 03 — 15 January 2008 TDA9899 [1] f Sound BP; FMPLL (MHz) recommended for W1[3] 0 5.5 M/N standard 0 5.5 B/G standard 0 5.5 I standard 0 5 ...
Page 24
... CVBS at pin CVBS AND digital zero IF I/Q at pins OUT1A, OUT1B and OUT2A, OUT2B analog CVBS at pin CVBS AND digital low IF at pins OUT1A and OUT1B Rev. 03 — 15 January 2008 TDA9899 output switch FM switch FM AGC external FM input amplifier EXTFMI OUT1A ...
Page 25
... Rev. 03 — 15 January 2008 TDA9899 PLL GATE Table 27 f (MHz) VIF TV1 = 0 (TSS) TV1 = 1 (QSS) 38.0 38.0 38.5 38.375 39.0 38.875 39.5 39.875 32.0 32.25 32.5 32.625 32.5 33.9 33.0 33.125 33.5 33.625 38.0 38.0 38.5 38.375 39 ...
Page 26
... DEEM de-emphasis off AGAIN[1:0] audio gain (only for FM mode (only for FM mode) Rev. 03 — 15 January 2008 TDA9899 DEEMT DEEM AGAIN1 © NXP B.V. 2008. All rights reserved. 0 AGAIN0 26 of 103 ...
Page 27
... VIF AGC hold (for diversity detection VIF AGC external IFIN[1:0] DIF/SIF input 00 = IF1A/B input 01 = IF3A/B input 10 = not used 11 = IF2A/B input VIFIN VIF input 1 = IF1A/B input 0 = IF2A/B input Rev. 03 — 15 January 2008 TDA9899 AGCSW IFIN1 IFIN0 Table 32 Table 40) Table 33 Table 34 © NXP B.V. 2008. All rights reserved. ...
Page 28
... V VIF AGC from internal > VIF AGC from pin AGCVIN < VIF AGC is not on hold > VIF AGC is on hold Rev. 03 — 15 January 2008 TDA9899 Output signal at OUT1A, OUT1B OUT2A, OUT2B zero IF I zero IF Q low IF off off direct IF ...
Page 29
... DTV (zero IF); low-pass cut-off frequency; TV2 = 0 and TV1 = 3.0 MHz 01 = 3.5 MHz 10 = 4.0 MHz 11 = not used DTV (low IF); upper BP cut-off frequency; TV2 = 0 and TV1 = 7.0 MHz 01 = 8.0 MHz 10 = 9.0 MHz 11 = not used SFREQ[5:0] synthesizer frequencies; see Table 16 Rev. 03 — 15 January 2008 TDA9899 SFREQ3 SFREQ2 SFREQ1 [1] Table 37 and Table 38 W1[3] and W1[4] and Table 17. ...
Page 30
... Rev. 03 — 15 January 2008 TDA9899 f synth SFREQ1 SFREQ0 W5[1] W5 ...
Page 31
... DIF/SIF synthesizer frequency for zero IF Japan (using bit TWOFLO = 1) SFREQ4 SFREQ3 SFREQ2 W5[4] W5[3] W5[ Rev. 03 — 15 January 2008 TDA9899 …continued f synth SFREQ1 SFREQ0 W5[1] W5 ...
Page 32
... Table AGC mode and behavior VIF AGC; MOD = 1 AGC1 W6[4] 0 normal 1 off (minimum gain) 0 fast 1 2nd fast Table 24 W2[7] and Rev. 03 — 15 January 2008 TDA9899 3 2 FMWIDE1 TWOFLO AUDIOPRO [1] Table 41 bit FMWIDE0 [2] 17. [1] SIF AGC normal off (minimum gain) normal fast Table 25 ...
Page 33
... W8 - data write register bit allocation data write register bit description Symbol Description - 0 = fixed value EASY[3:0] easy setting; see Table 46 Rev. 03 — 15 January 2008 TDA9899 PORT FILOUTBP NYQOFF [1] Table 33 Figure EASY3 EASY2 EASY1 © NXP B.V. 2008. All rights reserved. ...
Page 34
... TOPNEG2 TOPNEG1 Figure 46 Table 49 TDA9899 TOPNEG0 © NXP B.V. 2008. All rights reserved. ...
Page 35
... Figure see Figure 57.9 typical ). acc(set)TOP C-bus or potentiometer TOP adjustment (dB V) TOPPOS1 TOPPOS0 W10[1] W10[ typical : : see Figure 12 [ see Figure typical ). acc(set)TOP2 TDA9899 1 0 Table 52 © NXP B.V. 2008. All rights reserved 103 ...
Page 36
... Hz); input level (RMS) (sync level for B/G; peak white level AF i(IF) Conditions Rev. 03 — 15 January 2008 TDA9899 Conditions Min Max - all pins except ground 0 to ground TDA9899HL (LQFP48) - TDA9899HN (HVQFN48) - [1] human body model - [2] machine model - Conditions Typ in free air; 2 layer board 67 48 ...
Page 37
... VIF all standards except M/N M/N standard kHz LF( 3dB) measured on pins IF1A and IF1B or IF2A and IF2B; maximum IF gain; negative modulation mode W2[ and PLL set to overmodulation mode W2[ and W2[ Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max [2] 2.5 3.0 3.5 [2] - 3.3 4 ...
Page 38
... Figure 8 W4[ W7[ W4[ W7[ W4[ W7[ W4[ W7[ difference between L and B/G standard W4[ W7[ W4[ W7[ W4[ W7[ W4[ W7[ W4[ W7[ W4[ W7[ for emitter-follower AC and gain control 30 dB gain control negative modulation Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - ...
Page 39
... Hz; ripple video signal; grey level; positive and negative modulation; see Figure 9 [12] Figure 20 0.5 MHz to 2.5 MHz 2.5 MHz to 3.6 MHz 3.6 MHz to 3.8 MHz 3.8 MHz to 4.2 MHz = 4.5 MHz SC1 kHz SC1 Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - - 3 [ [8] ...
Page 40
... MHz to 5 MHz 5 MHz to 5.5 MHz = 6.0 MHz SC1 kHz SC1 f = 6.55 MHz; car(NICAM 250 kHz car(NICAM) see Figure 25 0.5 MHz to 3.1 MHz 3.1 MHz to 4.5 MHz 4.5 MHz to 4.8 MHz 4.8 MHz to 5.1 MHz Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max [13 + ...
Page 41
... Figure 8 AC load: C < > video signal; unified weighting filter ( “ITU-T J.61” ); see Figure 19 M/N standard; 50 IRE grey video signal; see Figure 19 Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max ...
Page 42
... VIF step; positive modulation 20 dB fast mode normal mode L standard see Table (sink) Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max 1 ...
Page 43
... AGC takeover 100 A sink(TAGC) W9[4: 0000 W9[4: 0000 W9[4: 1111 TAGC charge current normal mode fast mode activated by internal level detector TAGC discharge current TAGC W9[4: 0000 pin operating as current output Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - - 0 ...
Page 44
... V to 3.5 V Figure 13 pin open-circuit adjustment of VIF AGC based TAGC loop W10[ external resistor operation W10[ forced 2 I C-bus operation Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - - 0.3 [ ...
Page 45
... MHz VIF deviation 2 read-out via I C-bus; R1[4: MHz 0 ref MHz AFC ref 2 read-out via I C-bus; R1[4: MHz 0 ref MHz AFC ref Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - [3] 0.2 - 0.55V [ ...
Page 46
... FM AGC; see Table 22 AM mode output pin AUD permissible overload FM and AM mode W6[ W4[ MHz SIF W2[ W2[ W6[ W4[ MHz SIF W2[ W2[ Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit - ...
Page 47
... SIF step of 20 dB; FM mode; fast AGC increasing decreasing FM mode V = 100 V SIF SIF V = 140 mV SIF AM mode V = 100 V SIF SIF V = 140 mV SIF VCO LFSYN2 Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit ...
Page 48
... MHz multiple 500 kHz synthesizer spurious performance > 50 dBc nominal differential output voltage dependent on power supply ripple at 70 Hz; see Figure 9 for emitter-follower DC and AC; with external resistor to GND Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - ...
Page 49
... SC1 on; SC2 off IF intercarrier single-ended to GND; L standard; without modulation W7[ W7[ internal sound band-pass off band-pass off; 8 MHz to 0 MHz fundamental wave and harmonics IF intercarrier; L standard; without modulation Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit - - 25 - 800 - 90 140 ...
Page 50
... M/N, B D/K L/L-accent radio mode; BP selection for standard M/N B/G I D/K RADIO M/N, B/G, I, D/K or L/L-accent standard RADIO 10.7 M/N, B/G, I, D/K or L/L-accent standard RADIO 10 1.5 MHz c M/N, B/G, I, D/K or L/L-accent standard RADIO 10.7 Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit - 4.7 - MHz - 5.75 - MHz - 6.25 - MHz - 6.25 - MHz - 6 ...
Page 51
... SC2 off IF intercarrier; L standard; without modulation W7[ W7[ and DC see Table 18 and Table 4.5 MHz FMPLL f = 5.5 MHz FMPLL f = 6.0 MHz FMPLL f = 6.5 MHz FMPLL f = 10.7 MHz FMPLL Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit ...
Page 52
... W3[ W6[ window width = 1 MHz FMPLL LFFM f < 10 MHz f = 10.7 MHz W6[ W3[ W6[ W3[ Figure 14 AC-coupled via 4 pF gain controlled operation; W1[1: W1[1: W1[1: W1[1: W1[1: W1[1: Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit - ...
Page 53
... THD < pre-emphasis off FM window width = 237.5 kHz audio gain; FM deviation 100 kHz FM window width = 475 kHz audio gain; FM deviation 300 kHz Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max - - 1.8 400 500 ...
Page 54
... AM kHz Hz; ripple see Figure 9 AC-coupled DC-coupled 25 kHz FM deviation de-emphasis; see Table AM see Table Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max 80 100 - ...
Page 55
... W6[ (audio processing on); interference at 90 kHz AF and 40 kHz FM deviation W3[ (without de-emphasis); W6[ (audio processing on); interference at 90 kHz AF and 40 kHz FM deviation; see Figure 33 and Figure signal Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max [19] - 150 - - 1.7 - ...
Page 56
... MHz FMPLL f = 5.5 MHz FMPLL f = 6.0 MHz FMPLL f = 6.5 MHz FMPLL f = 10.7 MHz FMPLL V < (p-p); AUD 0 dB attenuation sink or source Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit - 50 150 mV 350 - +350 mV 150 - +150 ...
Page 57
... MHz 3 kHz sound carrier subharmonics 2.87 MHz 3 kHz Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max Unit - 2 ...
Page 58
... MHz 3 kHz 54 % modulation 54 % modulation; BP on; see Figure 32 “ITU-R BS.468-4” off composite IF; VIF modulation = color bar; “ITU-R BS.468-4” and DC; sink or source Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max ...
Page 59
... Figure 35 of external reference signal source; AC-coupled to external reference signal source to switch off reference signal input by external resistor wired between pin FREF and GND R = 3.9 k swoff(FREF swoff(FREF) Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max [26 2.3 2.6 2.9 [3] - ...
Page 60
... V = 5.0 V; pin CC(I2C-bus) connected 3.3 V; pin CC(I2C-bus) open-circuit V = 2.5 V; pin CC(I2C-bus) connected to GND [29 5.0 V CC(I2C-bus 3.3 V CC(I2C-bus 2.5 V CC(I2C-bus) Rev. 03 — 15 January 2008 TDA9899 = 38.375 MHz; PC Figure 49; unless Min Typ Max 2.3 2.6 2.9 [3] 200 350 500 [3] 200 300 360 [ [3] 150 ...
Page 61
... A ------- - ; rad is the bandwidth (Hz the damping LF( 3dB) Table 25. In this way the full composite video TDA9899 = 38.375 MHz; PC Figure 49; unless Max Unit +0. +1.0 V +0.75 V +10 A +10 A 0.4 V 400 kHz Figure 18. The © NXP B.V. 2008. All rights reserved. ...
Page 62
... AF Comment recommended for single-carrier-sound, FM narrow recommended for single-carrier-sound, FM wide recommended for two-carrier-sound, FM narrow used for test circuit 38.375 38.375 33.625 33.825 31.825 40.125 - - - TDA9899 20 Hz and 3dB(AF)l MHz MHz MHz dB dB © NXP B.V. 2008. All rights reserved 103 ...
Page 63
... V 3.41 V 2.6 V 3.20 V 1.83 V 1.80 V 1 TDA9899 V (V) P 5.050 5.000 4.950 Rev. 03 — 15 January 2008 TDA9899 zero carrier level white level black level sync level mhc115 V P ripple t (s) 001aad497 © NXP B.V. 2008. All rights reserved 103 ...
Page 64
... V monitor(VIFAGC) ( (1) (2) ( 100 ( (dB 1.0 1.5 2.0 2.5 Rev. 03 — 15 January 2008 TDA9899 001aad353 5 V TAGC ( ( 110 130 V (dB V) i(VIF) 001aad493 3.0 3.5 V (V) AGCVIN © NXP B.V. 2008. All rights reserved 103 ...
Page 65
... Integral TAGC (W9); step width: 1 based TAGC (W10). 100 V i(IF) ( Rev. 03 — 15 January 2008 TDA9899 bit pattern W9[4:0] or W10[4:0] 2 C-bus register W9 or W10 008aaa034 ( TOP2 TOP2 001aaf640 © NXP B.V. 2008. All rights reserved 103 ...
Page 66
... V AGC(SIF) ( 100 120 20 V (dB V) i(EXTFMI) (1) AM. (2) FM. Fig 15. Typical SIF AGC characteristic measured at pin MPP2 Rev. 03 — 15 January 2008 TDA9899 001aad357 (1) ( 100 V i(SIF) © NXP B.V. 2008. All rights reserved. 120 ( 103 ...
Page 67
... Average; RC network at pin MPP2. Fig 17. Typical analog and digital AFC characteristic for RIF TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile bit AFCWIN (R1[7 37.375 37.875 38.375 bit CARRDET (R1[5 5.4 Rev. 03 — 15 January 2008 TDA9899 (1) (2) (3) (4) 38.875 39.375 39.875 f VIF (1) (2) ...
Page 68
... Product data sheet Multistandard hybrid IF processing including car mobile AFC MPP2 TDA9899 R2 60 S/N (dB) ( Rev. 03 — 15 January 2008 TDA9899 100 k nF 001aad440 001aad660 90 100 V (dB V) i(VIF) © NXP B.V. 2008. All rights reserved 103 ...
Page 69
... Korea) 250 200 150 100 ( (3) 50 (2) 100 150 200 250 Rev. 03 — 15 January 2008 TDA9899 001aad487 (1) (3) ( (MHz) 001aad365 (MHz) © NXP B.V. 2008. All rights reserved 103 ...
Page 70
... Rev. 03 — 15 January 2008 TDA9899 001aad488 ( (MHz) 001aad361 (MHz) © NXP B.V. 2008. All rights reserved 103 ...
Page 71
... Rev. 03 — 15 January 2008 TDA9899 (1) (2) ( 001aad489 8 f (MHz) 001aad363 8 f (MHz) © NXP B.V. 2008. All rights reserved 103 ...
Page 72
... Rev. 03 — 15 January 2008 TDA9899 (1) (2) ( 001aaf551 8 f (MHz) 001aaf552 8 f (MHz) © NXP B.V. 2008. All rights reserved 103 ...
Page 73
... Rev. 03 — 15 January 2008 (1) (2) ( TDA9899 001aad491 8 f (MHz) 001aad364 8 f (MHz) © NXP B.V. 2008. All rights reserved 103 ...
Page 74
... Fig 30. Typical sound BP amplitude frequency response at TV mode, normalized to BP TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile 10 0 ( 3.0 2.0 1.0 center frequency Rev. 03 — 15 January 2008 (1) (4) (3) (2) (6) 0 1.0 2 TDA9899 001aaf579 3.0 (MHz) c © NXP B.V. 2008. All rights reserved 103 ...
Page 75
... Product data sheet Multistandard hybrid IF processing including car mobile 10 0 ( 3.0 2.0 1.0 BP center frequency 2.0 1.5 1.0 0 Rev. 03 — 15 January 2008 TDA9899 001aaf578 (1) (4) (3) (2) (6) 0 1.0 2 (MHz) c 001aad359 (kHz) AF © NXP B.V. 2008. All rights reserved. 3 103 ...
Page 76
... W7[ signal using variable FM deviation at 90 kHz (1) f (Hz W7[ variable FM deviation at 90 kHz AF Rev. 03 — 15 January 2008 TDA9899 001aah582 (kHz) 001aaf466 0 G (dB (kHz) © NXP B.V. 2008. All rights reserved. ...
Page 77
... Product data sheet Multistandard hybrid IF processing including car mobile 55 (S/N) w (dB Reference frequency input signal taken from external quartz circuit. Rev. 03 — 15 January 2008 TDA9899 001aaf468 100 150 200 V (mV) i(FREF)(RMS) © NXP B.V. 2008. All rights reserved 103 ...
Page 78
... Video signal related peak-to-peak levels are divided by factor order to conform with the RMS value scale of the secondary y-axis, but disregarding the none sine wave signal content. adjustment-related minimum IF gain. adjustment-related minimum IF gain. Rev. 03 — 15 January 2008 TDA9899 (2) IF gain control range ...
Page 79
... W4[ W4[ [2][5][ 33.4 MHz; o see Figure (RMS) i(IF 0.5 mV (RMS) i(IF) input signals 47.0 MHz i and 57.5 MHz; output signals 36.5 MHz or o 68.0 MHz; see Figure 39 W4[ W4[ Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max 1.8 1.93 2 1.8 2.0 2.2 2.0 2.5 - [3] 1 ...
Page 80
... MHz bandwidth BP off 6 MHz bandwidth 7 MHz bandwidth 8 MHz bandwidth 6 MHz band MHz 7 MHz band 13.75 MHz 7 MHz band MHz 8 MHz band 15.75 MHz 8 MHz band MHz Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max [ [4] ...
Page 81
... MHz to end of band single-ended AC load pF 3.0 MHz bandwidth 3.5 MHz bandwidth 4.0 MHz bandwidth BP off 3.0 MHz bandwidth 3.5 MHz bandwidth 4.0 MHz bandwidth Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max [ 200 [ 160 - 90 ...
Page 82
... MHz or o 2.9 MHz; see Figure 40 [2][4] 0.437 MHz to end of band [2][ mismatch between I and Q channel mismatch between I and Q channel 2.2 V AGCDIN Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max [2] ...
Page 83
... AGC detector; I C-bus setting corresponds to W9[4: 0000 before activating; V i(IF) below th(fast)AGC VCO LFSYN1 I / LFSYN1 VCO Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max - 0.20 0.27 0. ...
Page 84
... Figure kHz at 10 kHz at 100 kHz at 1.4 MHz multiple 500 kHz synthesizer spurious performance > 50 dBc Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max ...
Page 85
... AC-coupled to external reference signal source to switch off reference signal input by external resistor wired between pin FREF and GND R = 3.9 k swoff(FREF swoff(FREF) Rev. 03 — 15 January 2008 TDA9899 via broadband transformer Figure 49 Min Typ Max 2.3 2.6 2.9 [ ...
Page 86
... It depends on the used type of crystal. pull [10] For driving three reference frequency inputs via decoupling capacitors in parallel (three times TDA9899, pin FREF, W7[ and a single-ended capacitive load up to 6.5 pF the recommended value of the resistor to GND ...
Page 87
... LF bandwidth (Hz L(dif) (pF W4[ nominal output level = 40 MHz, with single-ended resistors GND. max = 9 MHz. max = 4 MHz. max Rev. 03 — 15 January 2008 TDA9899 [1] [2] C (nF) LFSYN2 4.7 4.7 4.7 4.7 4 ------ -K C ...
Page 88
... Rev. 03 — 15 January 2008 001aaf467 (1) (2) ( 110 V (dB V) i(IF)(RMS) (V) 0.5 ( 36.5 47 57.5 output signal V o(dif)(p-p) (V) 1.0 ( 1.1 1.7 2.3 output signal TDA9899 (MHz) 008aaa051 IM 2 (MHz) 008aaa052 © NXP B.V. 2008. All rights reserved 103 ...
Page 89
... Rev. 03 — 15 January 2008 (V) 0.5 ( 4.1 4.7 5.3 output signal ( 1.31 2.62 3.93 5.24 6.55 output signal 001aad494 t d(grp)LIF (ns) (1) (2) (3) 100 0 (3) 100 200 (MHz) (1) (2) (3) TDA9899 IM 5 (MHz) 008aaa053 H(ib) 7. (MHz) 008aaa054 © NXP B.V. 2008. All rights reserved 103 ...
Page 90
... Rev. 03 — 15 January 2008 TDA9899 001aad495 ( (MHz) (3) 001aad496 (MHz) (3) © NXP B.V. 2008. All rights reserved 103 ...
Page 91
... Fig 46. Typical gain characteristic for AGCDIN control voltage TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile 100 (7) G (dB (1) (2) ( 0.5 1.0 W4[7] = 0). W4[7] = 0). Rev. 03 — 15 January 2008 TDA9899 008aaa089 (4) (5) (6) 1.5 2.0 2.5 3.0 3.5 V (V) AGCDIN © NXP B.V. 2008. All rights reserved 103 ...
Page 92
... MHz MHz synth 100 kHz kHz kHz. input voltage on pin FREF Rev. 03 — 15 January 2008 001aag285 200 300 400 500 V (mV) i(FREF)(RMS) TDA9899 © NXP B.V. 2008. All rights reserved 103 ...
Page 93
... Connect resistor if external reference signal is not used. (2) Connect resistor if crystal is not used. (3) Use of crystal is optional. (4) Application depends on synthesizer frequency; see (5) Optional. (6) See Table 56. Fig 48. Application diagram of TDA9899 TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile tuner 4 MHz AGC reference ...
Page 94
... C par 220 nF FM PLL (5) loop filter 330 VIF output to FM input loop filter sound BPF from sound BPF Table 59. Rev. 03 — 15 January 2008 TDA9899 synthesizer trap control loop filter 3.3 k (2) 4 MHz (3) 470 AGC or diversity analog 100 sample-and-hold ground control switch ...
Page 95
... 0.27 0.18 7.1 7.1 9.15 9.15 0.5 0.17 0.12 6.9 6.9 8.85 8.85 REFERENCES JEDEC JEITA MS-026 Rev. 03 — 15 January 2008 detail 0.75 0.95 1 0.2 0.12 0.1 0.45 0.55 EUROPEAN PROJECTION TDA9899 SOT313 ( 0.55 0 ISSUE DATE 00-01-19 03-02-25 © NXP B.V. 2008. All rights reserved 103 ...
Page 96
... 7.1 5.25 7.1 5.25 0.5 5.5 6.9 4.95 6.9 4.95 REFERENCES JEDEC JEITA MO-220 - - - Rev. 03 — 15 January 2008 detail 0.5 0.05 0.1 5.5 0.1 0.05 0.3 EUROPEAN PROJECTION TDA9899 SOT619 ISSUE DATE 01-08-08 02-10-18 © NXP B.V. 2008. All rights reserved 103 ...
Page 97
... Table 60 TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile and 61 Rev. 03 — 15 January 2008 TDA9899 stg(max) Figure 52) than a PbSn process, thus © NXP B.V. 2008. All rights reserved the 97 of 103 ...
Page 98
... MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature MSL: Moisture Sensitivity Level Rev. 03 — 15 January 2008 3 ) 350 220 220 3 ) 350 to 2000 > 2000 260 260 250 245 245 245 peak temperature TDA9899 time 001aac844 © NXP B.V. 2008. All rights reserved 103 ...
Page 99
... DBS, DIP, HDIP, RDBS, SDIP, SIL [4] Through-hole-surface PMFP mount TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile [1] Soldering method Wave suitable suitable not suitable Rev. 03 — 15 January 2008 TDA9899 [2] Reflow [3] not suitable Dipping suitable © NXP B.V. 2008. All rights reserved 103 ...
Page 100
... Wave [5] , LBGA, not suitable [5] , TFBGA, not suitable , SO, SOJ suitable not recommended not recommended [10] [10] , WQCCN..L not suitable Rev. 03 — 15 January 2008 TDA9899 …continued [2] Reflow suitable [6] suitable suitable [7][8] suitable [9] suitable not suitable © NXP B.V. 2008. All rights reserved. Dipping 10 C 100 of 103 ...
Page 101
... TDA9899_3 Product data sheet Multistandard hybrid IF processing including car mobile Data sheet status Change notice Product data sheet - Product data sheet - Product data sheet - Rev. 03 — 15 January 2008 TDA9899 Supersedes TDA9899_2 TDA9899HL_ TDA9899HN_1 - © NXP B.V. 2008. All rights reserved. 101 of 103 ...
Page 102
... Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners C-bus — logo is a trademark of NXP B.V. http://www.nxp.com salesaddresses@nxp.com Rev. 03 — 15 January 2008 TDA9899 © NXP B.V. 2008. All rights reserved. 102 of 103 ...
Page 103
... Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2008. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TDA9899 All rights reserved. Date of release: 15 January 2008 Document identifier: TDA9899_3 ...