lu82562ex Intel Corporation, lu82562ex Datasheet - Page 29
lu82562ex
Manufacturer Part Number
lu82562ex
Description
Dual Footprint
Manufacturer
Intel Corporation
Datasheet
1.LU82562EX.pdf
(66 pages)
- Current page: 29 of 66
- Download datasheet (898Kb)
4.0
4.1
4.1.1
General Layout Considerations for Ethernet Controllers
Guidelines for Component Placement
Ethernet Component Layout Guidelines
These sections provide recommendations for performing printed circuit board layouts. Good layout
practices are essential to meet IEEE PHY conformance specifications and EMI regulatory
requirements.
Critical signal traces should be kept as short as possible to decrease the likelihood of being affected
by high frequency noise from other signals, including noise carried on power and ground planes.
Keeping the traces as short as possible can also reduce capacitive loading.
Since the transmission line medium extends onto the printed circuit board, special attention must
be paid to layout and routing of the differential signal pairs.
Designing for Gigabit operation is very similar to designing for 10 and 100 Mbps. For the
82547GI(EI) Gigabit Ethernet controller, system level tests should be performed at all three speeds.
Component placement can affect signal quality, emissions, and component operating temperature.
This section provides guidelines for component placement.
Careful component placement can:
Minimizing the amount of space needed for the Ethernet LAN interface is important because other
interfaces will compete for physical space on a motherboard near the connector. The Ethernet LAN
circuits need to be as close as possible to the connector (see
•
•
Decrease potential problems directly related to electromagnetic interference (EMI), which
could cause failure to meet applicable government test specifications.
Simplify the task of routing traces. To some extent, component orientation will affect the
complexity of trace routing. The overall objective is to minimize turns and crossovers between
traces.
82562EZ(EX)/82547GI(EI) Dual Footprint Design Guide
Figure
5).
21
Related parts for lu82562ex
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel Strataflash Memory28F128J3 28F640J3 28F320J3
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel IXP2325 Network Processor
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel IXP2400 Network Processor
Manufacturer:
Intel Corporation
Datasheet:
Part Number:
Description:
Intel IXP2805 Network Processor
Manufacturer:
Intel Corporation
Part Number:
Description:
Intel 82801DBM I/O Controller Hub 4 Mobile (ICH4-M), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet: