m29f002b-70p6tr STMicroelectronics, m29f002b-70p6tr Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
m29f002b-70p6tr
Manufacturer Part Number
m29f002b-70p6tr
Description
2 Mbit 256kb X8, Boot Block Single Supply Flash Memory
Manufacturer
STMicroelectronics
Datasheet
1.M29F002B-70P6TR.pdf
(21 pages)
M29F002BT, M29F002BB, M29F002BNT, M29F002BNB
Figure 2. PLCC Connections
SUMMARY DESCRIPTION
The M29F002B is a 2 Mbit (256Kb x8) non-volatile
memory that can be read, erased and repro-
grammed. These operations can be performed us-
ing a single 5V supply. On power-up the memory
defaults to its Read mode where it can be read in
the same way as a ROM or EPROM. The
M29F002B is fully backward compatible with the
M29F002.
The memory is divided into blocks that can be
erased independently so it is possible to preserve
valid data while old data is erased. Each block can
be protected independently to prevent accidental
Program or Erase commands from modifying the
memory. Program and Erase commands are writ-
ten to the Command Interface of the memory. An
on-chip Program/Erase Controller simplifies the
process of programming or erasing the memory by
taking care of all of the special operations that are
required to update the memory contents. The end
of a program or erase operation can be detected
and any error conditions identified. The command
set required to control the memory is consistent
with JEDEC standards.
The blocks in the memory are asymmetrically ar-
ranged, see Tables 3A and 3B, Block Addresses.
The first or last 64 Kbytes have been divided into
four additional blocks. The 16 Kbyte Boot Block
can be used for small initialization code to start the
2/21
DQ0
A7
A6
A5
A4
A3
A2
A1
A0
9
M29F002BNB
M29F002BB
M29F002BT
17
1
32
25
AI02959B
A14
A13
A8
A9
A11
G
A10
E
DQ7
microprocessor, the two 8 Kbyte Parameter
Blocks can be used for parameter storage and the
remaining 32K is a small Main Block where the ap-
plication may be stored.
Chip Enable, Output Enable and Write Enable sig-
nals control the bus operation of the memory.
They allow simple connection to most micropro-
cessors, often without additional logic.
The memory is offered in TSOP32 (8 x 20mm),
PLCC32 packages and it is supplied with all the
bits erased (set to ’1’).
In order to meet environmental requirements, ST
offers the M29F002B in ECOPACK
ECOPACK packages are Lead-free. The category
of second Level Interconnect is marked on the
package and on the inner box label, in compliance
with JEDEC Standard JESD97. The maximum rat-
ings related to soldering conditions are also
marked on the inner box label.
ECOPACK is an ST trademark. ECOPACK speci-
fications are available at: www.st.com.
Figure 3. TSOP Connections
V CC
A11
A13
A14
A17
A16
A15
A12
RP
A9
A8
A7
A6
A5
A4
W
1
8
9
16
M29F002BT
M29F002BB
AI02958
32
25
24
17
®
packages.
G
A10
E
DQ7
DQ6
DQ5
DQ4
DQ3
V SS
DQ2
DQ1
DQ0
A0
A1
A2
A3