rc1584 Fairchild Semiconductor, rc1584 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
rc1584
Manufacturer Part Number
rc1584
Description
7a Adjustable/fixed Low Dropout Linear Regulator
Manufacturer
Fairchild Semiconductor
Datasheet
1.RC1584.pdf
(12 pages)
PRODUCT SPECIFICATION
Load Regulation
It is not possible to provide true remote load sensing because
the RC1584 series are three-terminal devices. Load regula-
tion is limited by the resistance of the wire connecting the
regulators to the load. Load regulation per the data sheet
specification is measured at the bottom of the package.
For fixed voltage devices, negative side sensing is a true
Kelvin connection with the ground pin of the device returned
to the negative side of the load. This is illustrated in
Figure 12.
For adjustable voltage devices, negative side sensing is a true
Kelvin connection with the bottom of the output divider
returned to the negative side of the load. The best load regu-
lation is obtained when the top of resistor divider R1 con-
nects directly to the regulator output and not to the load.
Figure 13 illustrates this point.
If R1 connects to the load, then the effective resistance
between the regulator and the load would be:
R
The connection shown in Figure 13 does not multiply R
the divider ratio. As an example, R
per foot with 16-gauge wire. This translates to 4mV per foot
at 1A load current. At higher load currents, this drop repre-
sents a significant percentage of the overall regulation. It is
important to keep the positive lead between the regulator and
the load as short as possible and to use large wire or PC
board traces.
REV. 1.0.5 7/13/00
V
V
P
OUT
IN
Figure 12. Connection for Best Load Regulation
(1 + R2/R1), R
+
= V
V
IN
REF
C1
10 F
Figure 11. Basic Regulator Circuit
(1 + R2/R1) + I
IN
RC1584-1.5
IN
I
35 A
ADJ
GND
RC1584
P
ADJ
= Parasitic Line Resistance
OUT
OUT
ADJ
(R2)
LINE RESISTANCE
V
REF
P
PARASITIC
is about four milliohms
R
P
65-1584-17
R1
R2
+
C2
22 F
R
65-1584-14
L
V
P
OUT
by
Thermal Considerations
The RC1584 series protect themselves under overload condi-
tions with internal power and thermal limiting circuitry.
However, for normal continuous load conditions, do not
exceed maximum junction temperature ratings. It is impor-
tant to consider all sources of thermal resistance from junc-
tion-to-ambient. These sources include the junction-to-case
resistance, the case-to-heat sink interface resistance, and the
heat sink resistance. Thermal resistance specifications have
been developed to more accurately reflect device tempera-
ture and ensure safe operating temperatures.
For example, look at using an RC1584T to generate 7A @
1.5V 2% from a 3.3V source (3.135V to 3.465V).
Assumptions:
• V
• V
• I
• T
•
The power dissipation in this application is:
P
From the specification table:
T
The junction temperature is below the maximum rating.
D
J
a thermally conductive material)
= T
= 40 + (13.97) * (3 + 3) = 124 C
OUT
= (V
A
Case-to-Ambient
IN
OUT
Figure 13. Connection for Best Load Regulation
= 40 C
A
V
= 3.465V worst case
*
IN
IN
+ (P
= 7A continuous
CONNECT R1 TO CASE
CONNECT R2 TO LOAD
= 1.47V worst case
– V
D
IN
OUT
) * (
RC1584
) * (I
ADJ
Case-to-Ambient
= 3 C/W (assuming both a heatsink and
OUT
OUT
) = (3.465 – 1.47) * (7) = 13.97W
LINE RESISTANCE
PARASITIC
R1*
R2*
+
R
JC
P
)
65-1584-15
R
L
RC1584
7