lpc1810 NXP Semiconductors, lpc1810 Datasheet - Page 15

• Manufacturer Part Number: lpc1810
• Description: Lpc1850/30/20/10 32-bit Arm Cortex-m3 Mcu; Up To 200 Kb Sram; Ethernet, Two High-speed Usb, Lcd, And External Memory Controller
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC1850_30_20_10
Objective data sheet
Symbol
P6_6
P6_7
P6_8
P6_9
P6_10
P6_11
P6_12
P7_0
P7_1
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
Pin description
L14
J13
H13
J15
H15
H12
G15 I; PU
B16
C14
…continued
Reset
state
[1]
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
Type Description
I/O
O
-
O
-
I/O
-
O
-
I/O
-
O
I/O
-
-
O
I/O
O
-
O
I/O
-
-
O
I/O
O
-
O
I/O
O
-
O
I/O
O
I/O
O
All information provided in this document is subject to legal disclaimers.
GPIO0[5] — General purpose digital input/output pin.
EXTBUS_BLS1 — LOW active Byte Lane select signal 1.
n.c.
USB0_PWR_FAULT — Port power fault signal indicating overcurrent
condition; this signal monitors over-current on the USB bus (external circuitry
required to detect over-current condition).
n.c.
EXTBUS_A15 — External memory address line 15.
n.c.
USB0_IND1 — USB0 port indicator LED control output 1.
n.c.
EXTBUS_A14 — External memory address line 14.
n.c.
USB0_IND0 — USB0 port indicator LED control output 0.
GPIO3[5] — General purpose digital input/output pin.
n.c.
n.c.
EXTBUS_DYCS0 — SDRAM chip select 0.
GPIO3[6] — General purpose digital input/output pin.
MCABORT — Motor control PWM, LOW-active fast abort.
n.c.
EXTBUS_DQMOUT1 — Data mask 1 used with SDRAM and static devices.
GPIO3[7] — General purpose digital input/output pin.
n.c.
n.c.
EXTBUS_CKEOUT0 — SDRAM clock enable 0.
GPIO2[8] — General purpose digital input/output pin.
CTOUT_7 — SCT output 7. Match output 3 of timer 1.
n.c.
EXTBUS_DQMOUT0 — Data mask 0 used with SDRAM and static devices.
GPIO3[8] — General purpose digital input/output pin.
CTOUT_14 — SCT output 14. Match output 2 of timer 3.
n.c.
LCDLE — Line end signal.
GPIO3[9] — General purpose digital input/output pin.
CTOUT_15 — SCT output 15. Match output 3 of timer 3.
I2S_TX_WS — Transmit Word Select. It is driven by the master and received
by the slave. Corresponds to the signal WS in the I
LCDVD19 — LCD data.
Rev. 1.2 — 17 February 2011
32-bit ARM Cortex-M3 microcontroller
LPC1850/30/20/10
2
S-bus specification.
© NXP B.V. 2011. All rights reserved.
15 of 87