adum2400 Analog Devices, Inc., adum2400 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
adum2400
Manufacturer Part Number
adum2400
Description
Quad-channel Digital Isolators, 5kv
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADUM2400.pdf
(23 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adum2400ARWZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adum2400BRWZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adum2400BRWZ-RL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adum2400BRWZ-RL7
Manufacturer:
ADI
Quantity:
9
Company:
Part Number:
adum2400CRWZ
Manufacturer:
ADI
Quantity:
2 780
Part Number:
adum2400CRWZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adum2400CRWZ-RL
Manufacturer:
AD
Quantity:
556
Preliminary Technical Data
NOTES
1
2
3
4
5
6
7
8
9
All voltages are relative to their respective ground.
Supply current values are for all four channels combined running at identical data rates. Output supply current values are specified with no output load present. The
supply current associated with an individual channel operating at a given data rate may be calculated as described in the Power Consumption section on page 20 .
See Figure 8 through Figure 10 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 11 through
Figure 14 for total I
The minimum pulsewidth is the shortest pulsewidth at which the specified pulsewidth distortion is guaranteed.
The maximum data rate is the fastest data rate at which the specified pulsewidth distortion is guaranteed.
t
is measured from the 50% level of the rising edge of the V
t
load within the recommended operating conditions.
Co-directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing-directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels
with inputs on opposing sides of the isolation barrier.
CM
than can be sustained while maintaining V
transient magnitude is the range over which the common mode is slewed.
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See Figure 8 through Figure 10 for
information on per-channel supply current for unloaded and loaded conditions. See Power Consumption section on page 19 for guidance on calculating per-
channel supply current for a given data rate.
PHL
PSK
H
propagation delay is measured from the 50% level of the falling edge of the V
is the magnitude of the worst-case difference in t
is the maximum common-mode voltage slew rate that can be sustained while maintaining V
DD1
and I
DD2
supply currents as a function of data rate for ADuM2400/ADuM2401/ADuM2402 channel configurations.
O
< 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The
PHL
or t
Ix
PLH
signal to the 50% level of the rising edge of the V
that will be measured between units at the same operating temperature, supply voltages, and output
Rev. PrD | Page 7 of 23
Ix
signal to the 50% level of the falling edge of the V
O
> 0.8V
ADuM2400/ADuM2401/ADuM2402
DD2
. CM
Ox
signal.
L
is the maximum common-mode voltage slew rate
Ox
signal. t
PLH
propagation delay